FRONT PASSENGER AIRBAG ASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the instrument panel passenger airbag assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system (for Mono camera type)	for Mono Camera type: Click here for Stereo Camera type: Click here
		Lane control system (for Stereo camera type)
		Parking support brake system*
		Pre-collision system (for Mono camera type)
		Pre-collision system (for Stereo camera type)
		Adaptive high beam system
		Lighting system (EXT) cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic View Monitor System	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here
Steering sensor (Including removal and installation)	Steering angle neutral point	Parking support brake system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Steering angle setting	Parking assist monitor system	Click here
	Steering angle setting	Panoramic view monitor system	Click here

*: When performing learning using the GTS. Click hereClick here

Tip:

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

Click here

PROCEDURE

Click here
PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

Note:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Note:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
Click here
REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here
Click here
REMOVE NO. 5 HEATER TO REGISTER DUCT

Click here
Click here
REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

Click here

Click here

REMOVE NO. 2 INSTRUMENT PANEL WIRE

*a	Lock Button
	Protective Tape
	Release in this Direction

Using a screwdriver, release the lock button and disconnect the airbag connector.

Note:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

Tip:

Tape the screwdriver tip before use.
Use the same procedure for the opposite side.

Detach the wire harness clamp and remove the No. 2 instrument panel wire.

Click here
REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:
Deployment Side
- When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
- If the airbag deploys for any reason, it may cause a serious accident.
1. Remove the 2 screws.
2. Hold Here
  
  Insert moulding remover B, into the side of the airbag door facing the rear of the vehicle and detach the hooks.
3. While holding the positions shown in the illustration, move the instrument panel passenger airbag assembly toward you, detach the hook near the front of the vehicle, and then remove the instrument panel passenger airbag assembly.

FRONT PASSENGER AIRBAG ASSEMBLY REMOVAL