FRONT DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here


  • Front door glass sub-assembly

  • Front door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

*1: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

    Click here

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  6. REMOVE DOOR ARMREST COVER

    Click here

  7. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  8. REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  10. REMOVE FRONT DOOR NO. 1 TRIM BRACKET

    Click here

  11. REMOVE FRONT DOOR SERVICE HOLE COVER

    Click here

  12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

    Click here

  13. REMOVE FRONT DOOR GLASS RUN

    Click here

  14. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

    Click here

  15. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

    Click here

  16. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

    Click here

  17. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY


    1. B007WUFC01
      *1 Front Door Lock Open Rod
      B007Z37 Remove in this Direction

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.

    3. When reusing the front door lock with motor assembly:


      1. B007ZKN

        Remove the door lock wiring harness seal from the front door lock with motor assembly.

  18. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY


    1. B007ZGX

      Using a screwdriver, disengage the 2 claws as shown in the illustration.

    2. B007YTLC01
      B007Z37 Remove in this Direction

      Disengage the 2 claws to remove the front door lock cover sub-assembly as shown in the illustration.

  19. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. B007XC2C01
      B007Z37 Remove in this Direction

      Remove the front door lock remote control cable assembly as shown in the illustration.

  20. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. B007WRHC01
      B007Z37 Remove in this Direction

      Remove the front door inside locking cable assembly as shown in the illustration.