CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door disassembly/reassembly are shown below.
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
---|---|---|---|
Disconnect cable from negative (-) battery terminal | Memorize steering angle neutral point | LKA/LDA System | |
Intelligent clearance sonar system*1 | |||
Pre-crash safety system | |||
Lighting system (EXT)
|
|||
Adaptive high beam system | |||
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) | Stop and start system | ||
Memorize steering angle neutral point | Parking assist monitor system (w/ Parallel parking assist function) | ||
Parking assist monitor system (w/o Parallel parking assist function) | |||
Panoramic view monitor system | |||
Initialize back door lock | Power door lock control system | ||
Reset back door close position | Power back door system | ||
|
Initialize Power Window Control System |
|
*1: When performing learning using the GTS.
Tech Tips
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE
PRECAUTION
Note
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel plug.
REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Using a moulding remover, disengage the 4 clips and 4 guides.
Disconnect the connector to remove the multiplex network master switch assembly with front door upper armrest base panel.
REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Using a moulding remover, disengage the 4 clips and 4 guides.
Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.
REMOVE DOOR ARMREST COVER
Remove the door armrest cover.
REMOVE COURTESY LIGHT ASSEMBLY
REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION
Remove the screw and front door No. 1 stiffener cushion.
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Protective Tape |
Apply protective tape to the front door panel as shown in the illustration.
Remove the 3 screws.
Remove in this Direction |
Using a clip remover, disengage the 10 clips and remove the front door trim board sub-assembly as shown in the illustration.
Disconnect each connector.
Remove in this Direction |
Disconnect the front door lock remote control cable assembly from the front door inside handle sub-assembly as shown in the illustration.
Remove in this Direction | |
*a | Push |
Disengage the 2 claws as shown in the illustration to disconnect the front door inside locking cable assembly and remove the front door trim board sub-assembly.
REMOVE SEAT MEMORY SWITCH (w/ Memory)
REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
Disengage the 6 claws and remove the front door inner glass weatherstrip as shown in the illustration.
REMOVE FRONT DOOR AIR DUCT
Remove the 4 screws.
Disengage the guide to remove the front door air duct.
REMOVE DOOR LOCK CONTROL KNOB BEZEL
Remove in this Direction |
Disengage the 2 claws and remove the door lock control knob bezel as shown in the illustration.
REMOVE FRONT DOOR TRIM POCKET
Remove the 8 screws and front door trim pocket.
REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY
REMOVE OUTER MIRROR PROTECTOR
REMOVE OUTER MIRROR INSTALL HOLE COVER
REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
REMOVE FRONT DOOR NO. 1 TRIM BRACKET
Remove the 2 screws and front door No. 1 trim bracket.
REMOVE FRONT DOOR SERVICE HOLE COVER
Disconnect the connector.
Turn the front door weatherstrip clip 45 degrees and remove the 4 front door weatherstrip clips as shown in the illustration.
Disengage the 5 clamps.
Disengage the 5 clips to remove the front door service hole cover.
REMOVE DOOR SIDE AIRBAG SENSOR
REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the hole plug.
for Driver Side:
Connect the multiplex network master switch assembly.
for Front Passenger Side:
Connect the power window regulator switch assembly.
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
for Driver Side:
Disconnect the multiplex network master switch assembly.
for Front Passenger Side:
Disconnect the power window regulator switch assembly.
Remove the 2 bolts.
Note
After the bolts are removed, do not allow the front door glass sub-assembly to fall.
Remove in this Direction (1) | |
Remove in this Direction (2) |
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
Note
Do not damage the front door glass sub-assembly.
REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
Disengage the 2 claws to remove the front door No. 2 service hole cover.
*a | Temporary Bolt |
Disconnect the connector.
Loosen the temporary bolt.
Note
Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.
Remove the 5 bolts.
Remove the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Remove in this Direction |
Remove the 2 bolts.
Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.
REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
Disengage the clamp.
Disengage the 2 claws.
Using a screwdriver, disconnect the connector.
Disengage in this Direction |
Disengage the 2 claws and move the lever as shown in the illustration.
Remove in this Direction |
Remove the front door outside handle assembly as shown in the illustration.
REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.
Tech Tips
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Tech Tips
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
Disengage the 2 guides and claw to remove the front door outside handle cover.
REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 3 claws to remove the front door front outside handle pad.
REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
Disengage the claw.
Remove in this Direction (1) | |
Remove in this Direction (2) |
Disengage the 3 guides to remove the front door rear outside handle pad as shown in the illustration.
REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
*A | Inside |
*B | Outside |
Using a T30 "TORX" socket wrench, remove the screw.
Slide the front door outside handle frame sub-assembly to disengage the claw and remove the front door outside handle frame sub-assembly.
REMOVE FRONT DOOR LOCK OPEN ROD
Remove in this Direction (1) | |
Remove in this Direction (2) |
Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
REMOVE FRONT DOOR CHECK ASSEMBLY
Nut | |
Bolt |
Remove the 2 nuts and bolt, and front door check assembly.
REMOVE FRONT DOOR WEATHERSTRIP
Double-sided Tape |
Using a clip remover, disengage the 25 clips and remove the front door weatherstrip.
REMOVE FRONT DOOR PANEL PROTECTOR
Remove the front door panel protector.
REMOVE FRONT DOOR VENT SEAL
Remove the front door vent seal.
REMOVE UPPER DOOR FRAME GARNISH
Disengage the 3 claws to remove the upper door frame garnish.
REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Bolt | |
Screw |
Remove the 2 bolts, screw and front door front lower frame sub-assembly.
REMOVE FRONT DOOR FIX WINDOW GLASS
Remove in this Direction |
Remove the front door fix window glass with the front door fix window weatherstrip as shown in the illustration.
Remove the front door fix window glass from the front door fix window weatherstrip.
REMOVE FRONT DOOR PANEL CUSHION
Disengage the claw to remove the front door panel cushion.
REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING
REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
REMOVE FRONT DOOR REAR OUTSIDE STRIPE
REMOVE FRONT DOOR STRIPE
REMOVE NO. 1 BLACK OUT TAPE
REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY
REMOVE FRONT DOOR SCUFF PLATE
REMOVE COWL SIDE TRIM BOARD
REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING