REAR SEATBACK HEATER(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the separate type rear seatback cover (rear seatback heater) removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	for 8GR-FKS: Click here for V35A-FTS: Click here
	Memorize steering angle neutral point	LKA/LDA system	Click here
		Parking support brake system*
		Pre-collision system
		Adaptive high beam system
		Lighting system (EXT) cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic View Monitor System	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here
Rear seat headrest assembly LH (Including removal and installation) Rear seat headrest assembly RH (Including removal and installation) Rear No.1 seat adjuster assembly (Including removal and installation) Rear No.2 seat adjuster assembly (Including removal and installation)	Initialize position control ECU	Rear power seat control system	Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.

Note

If the rear seat cushion airbag assembly LH was deployed, replace the rear seat cushion panel LH, rear seat cushion pad and separate type rear seat cushion cover with the necessary parts in accordance with the extent of the collision damage.
If the rear seat airbag assembly LH was deployed, replace the rear seat sub panel sub-assembly LH, separate type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage.
Replace any other damaged parts as necessary.

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

PROCEDURE

PRECAUTION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
1. Disconnect the cable from the negative (-) battery terminal.
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  
  If the airbag deploys for any reason, it may cause a serious accident.
  Note
  
  When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
  
  Click here
  1. for 8GR-FKS:
    
    Click here
  2. for V35A-FTS:
    
    Click here
REMOVE REAR SEAT CUSHION ASSEMBLY LH

Click here
REMOVE REAR SEAT CUSHION ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR SEAT CUSHION LOCK HOOK

Click here
REMOVE REAR SEATBACK ASSEMBLY LH

Click here
REMOVE REAR SEATBACK ASSEMBLY RH

Click here
REMOVE NO. 1 SEATBACK CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

Click here
REMOVE NO. 1 SEATBACK CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

Tech Tips

Use the same procedure described for the LH side.
REMOVE NO. 2 SEATBACK CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

Click here
REMOVE NO. 2 SEATBACK CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR SEAT HEADREST ASSEMBLY LH

Click here
REMOVE REAR SEAT HEADREST ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR SEAT HEADREST SUPPORT

Click here
REMOVE SEATBACK CHECK VALVE WITH BRACKET LH

Click here
REMOVE SEATBACK CHECK VALVE WITH BRACKET RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR SEAT WIRE LH

Click here
REMOVE REAR SEAT WIRE RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY LH

Click here
REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR SEATBACK MAIN FRAME SUB-ASSEMBLY LH

Click here
REMOVE REAR SEATBACK MAIN FRAME SUB-ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR NO. 2 SEAT HEADREST ADJUSTER SUB-ASSEMBLY

Click here
REMOVE REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY

Tech Tips

Use the same procedure described for the rear No. 2 seat headrest adjuster sub-assembly.
REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD LH

Click here
REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE SEPARATE TYPE REAR SEATBACK COVER LH
1. Pull out the strap and bracket of the separate type rear seatback cover LH from the hole of the separate type rear seatback pad LH.
2. Remove the 2 hog rings and separate type rear seatback cover LH.
REMOVE SEPARATE TYPE REAR SEATBACK COVER RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE SEAT COVER WIRE

Click here