REAR SEAT ASSEMBLY(for Power Seat) DISASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:


  • B006C5U

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • This may result in injury.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. REMOVE SEAT CUSHION CHECK VALVE WITH HOSE LH (w/ Refresh Seat)


    1. B006FTMC03
      *a Tube Clamp
      *b Tube
      B006AHR Joint
      B006EC9 Connector
      B006FCW Screw
      B006GBM Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

    2. Detach the tube clamp and remove the tube.

    3. Remove the tube from the clamp.

    4. Disconnect the connector.

    5. Remove the 3 screws and seat cushion check valve with hose LH.

  2. REMOVE SEAT CUSHION CHECK VALVE WITH HOSE RH (w/ Refresh Seat)


    1. B006CDCC03
      *a Tube Clamp
      *b Tube
      B006AHR Joint
      B006EC9 Connector
      B006FCW Screw
      B006GBM Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

    2. Detach the tube clamp and remove the tube.

    3. Remove the tube from the clamp.

    4. Disconnect the connector.

    5. Remove the 3 screws and seat cushion check valve with hose RH.

  3. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD LH


    1. B006ANZC01
      *a Wire Harness Clamp
      *b Hook

      Disconnect the 2 connectors.

    2. Detach the wire harness clamp.

    3. Detach the hook.

    4. w/ Refresh Seat:


      1. Pull out the tube from the hole of the rear seat cushion panel LH.

        B0069OG
    5. B006EVMC01
      B006GBM Protective Tape

      Using a thin-bladed screwdriver wrapped with protective tape, detach the claw and disconnect the connector of the occupant detection sensor.

    6. B006FOCC01
      B006DHE Remove in this Direction

      Pull out the connector of the occupant detection sensor and wire harness from the hole of the rear seat cushion panel LH and remove the separate type rear seat cushion cover with pad LH.

  4. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER LH


    1. Remove the 8 hog rings and pull out the strap from the hole of the rear seat cushion pad LH.

      B006DJH
    2. Remove the 6 hog rings and separate type rear seat cushion cover LH.

  6. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. REMOVE SEAT COVER WIRE


    1. B006DO8

      Remove the seat cover wire.

  8. REMOVE REAR SEAT CUSHION PAD (w/ Refresh Seat)


    1. Remove the 4 hog rings and pull out the strap from the hole of the rear seat cushion pad.

      B006FIYC01
      B006FQ2 Double-sided Tape - -
    2. Remove the double-sided tape and rear seat cushion pad.

  9. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B006CI4C01

      Cut the tack pin and fold back the strap.

    2. B006EC2

      Remove the 2 pieces of felt.

    3. B006EOAC01
      B006DHE Remove in this Direction

      Detach the hook and remove the seat cushion main stretcher cushion assembly.

  10. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  11. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B006GK7

      Cut the tack pin and fold back the strap.

    2. B006E0F

      Remove the 2 pieces of felt.

    3. B006EFHC02
      B006DHE Remove in this Direction

      Detach the hook and remove the seat cushion main stretcher cushion assembly.

  12. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE REAR SEAT CUSHION AIRBAG ASSEMBLY LH

    Click here

  14. REMOVE REAR SEAT CUSHION AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. REMOVE REAR NO. 2 SEAT WIRE LH


    1. B0069GLC01
      B006GBM Double-sided Tape

      Disconnect the connector.

    2. Detach the wire harness clamp.

    3. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the rear No. 2 seat wire LH.

  16. REMOVE REAR NO. 2 SEAT WIRE RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE REAR CENTER SEAT CUSHION COVER SUB-ASSEMBLY


    1. B006FX5C01
      *a Hog Ring
      *b Hook

      Remove the hog ring.

    2. Detach the hook and remove the rear center seat cushion cover sub-assembly.

  18. REMOVE REAR CENTER SEAT CUSHION PAD


    1. B006DQZC01
      B006GBM Double-sided Tape

      w/ Occupant Detection Sensor:


      1. Using a thin-bladed screwdriver wrapped with protective tape, detach the claw and disconnect the connector of the occupant detection sensor.

    2. Remove the rear center seat cushion pad from the center seat cushion frame sub-assembly.

  19. REMOVE REAR SEAT INNER BELT ASSEMBLY LH

    Click here

  20. REMOVE REAR SEAT INNER BELT ASSEMBLY RH

    Click here

  21. REMOVE REAR SEAT CENTER LAP TYPE BELT ASSEMBLY RH

    Click here

  22. REMOVE REAR NO. 2 SEAT WIRE LH

    Tech Tips

    Use the same procedure for the LH and RH sides.


    1. B006F9LC01
      B006DHE Remove in this Direction
      B006GBM Protective Tape

      Disconnect the connector.

    2. Detach the wire harness clamp.

    3. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the rear No. 2 seat wire LH.

  23. REMOVE REAR SEAT LEGREST ASSEMBLY

    Tech Tips

    Use the same procedure for the LH and RH sides.


    1. B006G3BC01
      B006DHE Remove in this Direction (1)
      B006B42 Remove in this Direction (2)

      Pull in the removal direction (1) shown in the illustration to detach the clip.

    2. Lift in the removal direction (2) shown in the illustration, detach the guide and remove the rear seat legrest assembly.

  24. REMOVE REAR SEAT LEGREST COVER

    Tech Tips

    Use the same procedure for the LH and RH sides.


    1. B006E41

      Remove the 5 screws and rear seat legrest cover.

  25. REMOVE REAR SEAT LEGREST COVER RH (w/ Ottoman)


    1. B006E2C

      Remove the 6 screws.

    2. Detach the guide and remove the rear seat legrest cover RH.

  26. REMOVE REAR SEAT LEGREST COVER (w/ Ottoman)


    1. B006F3H

      Remove the 6 screws and rear seat legrest cover.

  27. REMOVE REAR NO. 2 SEAT WIRE RH (w/ Ottoman)


    1. B006BGB

      Disconnect the 2 connectors.

    2. Detach the wire harness clamp.

    3. Detach the claw and remove the rear No. 2 seat wire RH.

  28. REMOVE REAR SEAT LEGREST ARM SUB-ASSEMBLY LH


    1. B0069M8

      Remove the 4 bolts and rear seat legrest arm sub-assembly LH.

  29. REMOVE REAR SEAT LEGREST ARM SUB-ASSEMBLY RH


    1. w/o Ottoman:


      1. Use the same procedure described for the LH side.

    2. B006D43

      w/ Ottoman:


      1. Remove the 4 bolts and rear seat legrest arm sub-assembly RH.

  30. REMOVE NO. 1 SEATBACK CHECK VALVE WITH HOSE LH (w/ Refresh Seat)


    1. B006DADC01
      B006FQ2 Fastening Tape

      Detach the fastening tape and fold back the separate type rear seatback cover LH.

    2. B006EY0

      Disconnect the connector.

    3. Detach the claw and connect the connector.

    4. B006CSXC01
      *a Clamp
      *b Hook
      *c Tube Clamp
      B006AHR Joint
      B006EC9 Connector
      B006FCW Clip
      B006GBM Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

    5. Remove the tube from the clamp.

    6. Remove the tube from the hook.

    7. Disconnect the connector.

    8. Remove the 4 clips.

    9. Detach the tube clamp and remove the No. 1 seatback check valve with hose LH.

  31. REMOVE NO. 1 SEATBACK CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE NO. 2 SEATBACK CHECK VALVE WITH HOSE LH (w/ Refresh Seat)


    1. B006AVKC01
      *a Clamp
      *b Tube Clamp
      B006AHR Joint
      B006EC9 Connector
      B006FCW Clip
      B006GBM Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claws and disconnect the joint.

    2. Remove the tube from the clamp.

    3. Detach the tube clamp and remove the tube.

    4. Disconnect the connector.

    5. Remove the 2 screws and No. 2 seatback check valve with hose LH.

  33. REMOVE NO. 2 SEATBACK CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  34. REMOVE REAR SEAT HEADREST ASSEMBLY LH


    1. B006BFOC01
      B006DHE Remove in this Direction

      Remove the 2 pins.

    2. B006C52C01
      B006DHE Remove in this Direction

      Remove the rear seat headrest assembly LH.

  35. REMOVE REAR SEAT HEADREST ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. REMOVE REAR SEAT HEADREST SUPPORT

    Tech Tips

    Use the same procedure for the LH and RH sides.


    1. B006FSK

      Detach the claw.

    2. B0069K6C01
      B006DHE Remove in this Direction

      Remove the 2 rear seat headrest supports.

  37. REMOVE SEATBACK CHECK VALVE WITH BRACKET LH


    1. B006ENN

      Detach the claw and remove the clamp.

    2. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

      B0069T7C01
      *A w/o Refresh Seat *B w/ Refresh Seat
      *a Clamp *b Tube Clamp
      B006AHR Joint B006EC9 Connector
      B006FCW Screw - -
    3. Remove the tube from the clamp.

    4. Detach the tube clamp and remove the tube.

    5. Disconnect the connector.

    6. Remove the 3 screws and seatback check valve with bracket LH.

  38. REMOVE SEATBACK CHECK VALVE WITH BRACKET RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. REMOVE REAR SEAT WIRE LH


    1. B006B9SC01
      *A w/ Refresh Seat
      B006EC9 Rear Seat Airbag Assembly LH Connector

      w/o Refresh Seat:


      1. Disconnect the 8 connectors.

    2. w/ Refresh Seat:


      1. Disconnect the 9 connectors.

    3. Disconnect the connector of the rear seat airbag assembly LH.


      1. Push down the white housing lock and slide the yellow CPA.

        B006G4FC28
        *a Housing Lock *b CPA

        Note


        • Do not pull while holding the wire harness.

        • Do not try to release the lock while holding down the top of the CPA (A in the illustration), as this prevents the lock from being released.

      2. Slide the yellow CPA while pushing down the white housing lock again, and disconnect the connector.

    4. Detach the wire harness clamp.

    5. B006AH6

      Detach the hook.

    6. B006BYP

      Remove the screw.

    7. Detach the guide and remove the plate.

    8. Pull out the connector holder from the rear No. 2 seat headrest adjuster.

      B006C1W
    9. B006DL7C01
      B006DHE Remove in this Direction

      Detach the claw and remove the connector holder.

    10. B006AYJC01
      B006DHE Remove in this Direction

      Pull out the connector from the No. 2 rear seat headrest adjuster and remove the rear seat wire LH.

  40. REMOVE REAR SEAT WIRE RH

    Tech Tips

    Use the same procedure described for the LH side.

  41. REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY LH


    1. Remove the tube from the clamp.

      B006CA3C01
      *A w/o Refresh Seat *B w/ Refresh Seat
    2. Remove the 2 nuts and lumbar support pump sub-assembly LH.

  42. REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  43. REMOVE POSITION CONTROL ECU ASSEMBLY LH


    1. B0069TB

      Remove the 2 nuts and position control ECU assembly LH.

  44. REMOVE POSITION CONTROL ECU ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  45. REMOVE REAR SEATBACK MAIN FRAME SUB-ASSEMBLY LH


    1. B006FCZC01
      *A w/ Refresh Seat

      w/ Refresh Seat:


      1. Detach the tube clamp and remove the tube.

    2. Remove the 4 nuts and rear seatback main frame sub-assembly LH.

  46. REMOVE REAR SEATBACK MAIN FRAME SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  47. REMOVE REAR NO. 2 SEAT HEADREST ADJUSTER SUB-ASSEMBLY


    1. B006BPO

      Remove the 2 nuts and rear No. 2 seat headrest adjuster sub-assembly.

  48. REMOVE REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY

    Tech Tips

    Use the same procedure described for the rear No. 2 seat headrest adjuster sub-assembly.

  49. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH


    1. B006A0YC01
      B006DHE Remove in this Direction

      Detach the claw and disconnect the seat heater control sub-assembly LH.

  50. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  51. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD LH


    1. Detach the hook.

      B006DH8C01
      *a Hook *b Wire Harness Clamp
    2. Pull out the tube from the separate type rear seatback cover LH.

    3. Detach the wire harness clamp.

    4. B006DWBC01
      B006DHE Remove in this Direction (1)
      B006B42 Remove in this Direction (2)

      Remove the nut and the 2 brackets of the separate type rear seatback cover LH.

    5. B006GM1

      Pull out the strap and bracket of the separate type rear seatback cover LH from the hole of the rear seat sub panel sub-assembly LH.

    6. w/ Refresh Seat:


      1. Remove the tube from the clamp.

        B006EXCC01
        *a Clamp *b Hook
      2. Remove the tube from the hook.

    7. Remove the separate type rear seatback cover with pad LH from the rear seat sub panel sub-assembly LH.

  52. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  53. REMOVE SEPARATE TYPE REAR SEATBACK COVER LH


    1. B006B73

      Pull out the strap and bracket of the separate type rear seatback cover LH from the hole of the separate type rear seatback pad LH.

    2. B006AJI

      Remove the 2 hog rings and separate type rear seatback cover LH.

  54. REMOVE SEPARATE TYPE REAR SEATBACK COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  55. REMOVE SEAT COVER WIRE


    1. Remove the seat cover wire and strap.

      B006CDW
  56. REMOVE REAR UPPER SEATBACK PAD B (w/ Refresh Seat)


    1. B006GFGC01
      B006FQ2 Double-sided Tape

      Remove the double-sided tape and rear upper seatback pad B.

  57. REMOVE REAR UPPER SEATBACK PAD A (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for rear upper seatback pad B.

  58. REMOVE SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B0069VS

      Remove the 3 pieces of felt.

    2. B006G8P

      Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type rear seatback pad LH.

    3. B006EB8

      Detach the hook and remove the seatback main stretcher cushion assembly.

  59. REMOVE SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  60. REMOVE SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B006E96

      Remove the 3 pieces of felt.

    2. B006A0V

      Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type rear seatback pad LH.

    3. B006GBAC01
      B006DHE Remove in this Direction

      Detach the hook and remove the seatback main stretcher cushion assembly.

  61. REMOVE SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  62. REMOVE REAR SEAT AIRBAG ASSEMBLY LH

    Click here

  63. REMOVE REAR SEAT AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  64. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH


    1. B006DO3

      Pull out the tube from the hole of the rear seat sub panel sub-assembly LH.

    2. Using a clip remover, detach the clip and remove the lumbar support adjuster assembly LH.

  65. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  66. REMOVE REAR SEATBACK SUPPORT LH


    1. B006FUZ

      Remove the tube from the clamp.

    2. Pull out the tube from the hole of the rear seat sub panel sub-assembly LH.

    3. Using a clip remover, detach the clip and remove the rear seatback support LH.

  67. REMOVE REAR SEATBACK SUPPORT RH

    Tech Tips

    Use the same procedure described for the LH side.

  68. REMOVE REAR CENTER NO. 2 SEAT ARMREST PANEL SUB-ASSEMBLY


    1. B006GMOC03
      B006DHE Remove in this Direction

      Detach the clip and claws.

    2. While moving the rear center No. 2 seat armrest panel sub-assembly in the direction indicated by the arrow shown in the illustration, detach the guide to remove it.

  69. REMOVE REAR CENTER NO. 2 SEAT ARMREST PANEL


    1. B006BPYC01
      B006DHE Remove in this Direction

      Detach the clip and claw.

    2. While moving the rear center No. 2 seat armrest panel in the direction indicated by the arrow shown in the illustration, detach the guide to remove it.

  70. REMOVE REAR POWER SEAT SWITH WITH BRACKET


    1. B006B1G

      Remove the 4 screws and disconnect the rear power seat switch with bracket from the rear center seat armrest assembly.

  71. REMOVE REAR CENTER SEAT ARMREST BRACKET LH


    1. B006EPV

      Remove the 2 screws and rear center seat armrest bracket LH.

  72. REMOVE REAR CENTER SEAT ARMREST BRACKET RH


    1. B006EWF

      Remove the 2 screws and rear center seat armrest bracket RH.

  73. REMOVE REAR CENTER SEAT ARMREST COVER


    1. B006BAM

      Remove the rear center seat armrest cover.

  74. REMOVE REAR POWER SEAT SWITCH


    1. B006BWM

      Disconnect the connector, detach the clamp and remove the rear power seat switch.

  75. REMOVE REAR CENTER SEAT CUP HOLDER TRAY


    1. B006DRM

      Detach the claw and remove the rear center seat cup holder tray.

  76. REMOVE REAR CENTER SEAT ARMREST CUP HOLDER SUB-ASSEMBLY


    1. B006CZ2

      Remove the 6 screws, detach the guide and remove the rear center seat armrest cup holder sub-assembly.

  77. REMOVE CENTER ARMREST LOCK SUB-ASSEMBLY


    1. B006EUCC01
      B006DHE Remove in this Direction
      B006AHR Screw

      Remove the 4 screws.

    2. Detach the guide and remove the center armrest lock sub-assembly in the direction indicated by the arrow shown in the illustration.

  78. REMOVE REAR CENTER SEAT ARMREST DOOR SUB-ASSEMBLY


    1. B006BCM

      Using a clip remover, remove the 2 console compartment door hinge shafts.

    2. B006EU5C01
      B006DHE Remove in this Direction (1)
      B006B42 Remove in this Direction (2)

      Slide the rear center seat armrest door sub-assembly in the removal direction (1) shown in the illustration and detach the hinge.

    3. Remove the rear center seat armrest door sub-assembly in the removal direction (2) shown in the illustration.

  79. REMOVE REAR CENTER NO. 2 SEAT ARMREST BOX


    1. B006AL5C01
      B006DHE Incline in this Direction
      B006B42 Remove in this Direction
      B006GBM Protective tape

      Apply protective tape to the rear center No. 2 seat armrest box to prevent damage.

    2. Insert a thin-bladed screwdriver with its tip wrapped with protective tape and push the HDMI cable cover toward the front of the vehicle.

    3. B006FXF

      Detach the claw and disconnect the wire harness from the HDMI cable cover.

    4. B006BRN

      Disconnect the 3 connectors.

    5. B0069LV

      Remove the 6 screws.

    6. B0069M4C01
      B006DHE Remove in this Direction

      Tilt the rear center No. 2 seat armrest box in the direction indicated by the arrow shown in the illustration.

    7. B0069ZVC01
      B006DHE Remove in this Direction

      Remove the rear center No. 2 seat armrest box as shown in the illustration.

  80. REMOVE HEADPHONE TERMINAL


    1. for LH Side:

      Click here

    2. for RH Side:

      Click here

  81. REMOVE USB CHARGER SOCKET

    Click here

  82. REMOVE CENTER ARMREST LOCK SUB-ASSEMBLY


    1. B006GD1C01
      B006DHE Remove in this Direction

      Detach the cable clamp and disconnect the cable.

    2. B006A7X

      Remove the 4 screws, detach the guide and remove the center armrest lock sub-assembly.

  83. REMOVE CENTER ARMREST HINGE COVER LH


    1. B006CU5C01
      B006DHE Remove in this Direction

      Detach the claw and guides and remove the center armrest hinge cover.

  84. REMOVE CENTER ARMREST HINGE COVER

    Tech Tips

    Use the same procedure described for the center armrest hinge cover LH.