BRAKE ACTUATOR REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR ENGINE UNDER COVER LH


    1. for 2AD-FHV:

      Click here

    2. for 2AD-FTV:

      Click here

    3. for 2AR-FE:

      Click here

    4. for 3ZR-FAE:

      Click here

    5. for 3ZR-FE:

      Click here

    6. for 2WW:

      Click here

  4. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    1. for 2AD-FHV:

      Click here

    2. for 2AD-FTV:

      Click here

    3. for 2AR-FE:

      Click here

    4. for 3ZR-FAE:

      Click here

    5. for 3ZR-FE:

      Click here

    6. for 2WW:

      Click here

  5. INSTALL NO. 3 COWL TOP PANEL INSULATOR (for 2WW)


    1. A01V70R

      Remove the 4 nuts and No. 3 cowl top panel insulator.

  6. REMOVE AIR CLEANER SUPPORT


    1. for 2AD-FHV:

      Click here

    2. for 2AD-FTV:

      Click here

  7. REMOVE FUEL FILTER ASSEMBLY


    1. for 2AD-FHV:

      Click here

    2. for 2AD-FTV:

      Click here

    3. for 2WW:

      Click here

  8. REMOVE AIR CLEANER BRACKET


    1. for 2AD-FHV:

      Click here

    2. for 2AD-FTV:

      Click here

  9. REMOVE FUEL FILTER SUPPORT (for 2WW)

    Click here

  10. DISCONNECT ENGINE WIRE


    1. except 2WW:


      1. A01V7O7

        Remove the bolt and detach the 2 clamps.

      2. A01V962

        Remove the bolt and wire harness clamp bracket.

    2. A01V71X

      for CVT


      1. Disconnect the connector.

      2. Remove the bolt and disconnect the engine wire.

  11. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)


    1. A01V9B5

      Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever.

    2. Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.

  12. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET (for Automatic Transmission)


    1. A01V9PT

      Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.

    2. Detach the clamp.

  13. DRAIN BRAKE FLUID

    Note

    Wash off brake fluid immediately if it comes in contact with any painted surface.

  14. REMOVE BRAKE ACTUATOR ASSEMBLY


    1. A01V8SK

      Release the lock lever and disconnect the connector from the brake actuator assembly.

      Note

      Be careful not to allow brake fluid to enter the removed connector.

    2. Disconnect the clamp from the brake actuator bracket assembly.

    3. A01VAO0

      Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

    4. A01VAT3C01
      *a to Front Wheel Cylinder RH
      *b to Front Wheel Cylinder LH
      *c to Rear Wheel Cylinder RH
      *d to Rear Wheel Cylinder LH
      *e from Front Master Cylinder
      *f from Rear Master Cylinder

      Use tags or make a memo to identify the places to reconnect.

    5. A01V6TB

      Remove the 4 bolts and brake actuator assembly from the brake actuator bracket assembly.

  15. REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY


    1. A01V9MN

      Remove the 3 nuts and brake actuator bracket assembly.

      Note

      Be careful not to damage the brake tubes.

    2. A01V943

      Disconnect the 3 clamps from the brake actuator bracket assembly.

  16. REMOVE BRAKE ACTUATOR CASE COLLAR


    1. A01V6VH

      Remove the 4 brake actuator case collars from the brake actuator bolt cushion.

  17. REMOVE BRAKE ACTUATOR BOLT CUSHION


    1. A01V7UL

      Remove the 4 brake actuator bolt cushions from the brake actuator bracket assembly.