ROOF HEADLINING INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. Attach the 4 claws and guide to install the front shoulder belt anchor plate sub-assembly LH.

  2. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B002BTVE03
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle and install a new rear door opening trim weatherstrip LH as shown in the illustration.

  4. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    B002BAOE03
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the front door opening trim weatherstrip LH with the mark position on the vehicle and install a new front door opening trim weatherstrip LH as shown in the illustration.

  6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL ROOF HEADLINING ASSEMBLY


    1. Insert the roof headlining assembly through the front door and move it as shown in the illustration.

      Note


      • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

      • Do not damage the roof headlining assembly or vehicle interior.

      B002B81

    2. w/ Sliding Roof:


      1. Attach the guide.

      2. Attach the 10 fasteners and 15 clips to install the roof headlining assembly.

        Note

        After installing the roof headlining assembly, make sure that the lip of the front door opening trim weatherstrip LH and RH and the rear door opening trim weatherstrip LH and RH is not pinched.

        B002B8YE02
        Text in Illustration
        *1 Guide *2 Fastener

    3. w/o Sliding Roof:


      1. Attach the 3 fasteners and 15 clips to install the roof headlining assembly.

        Note

        After installing the roof headlining assembly, make sure that the lip of the front door opening trim weatherstrip LH and RH and the rear door opening trim weatherstrip LH and RH is not pinched.

        B002BF3
    4. B002BPJ

      Connect the connector and attach the 3 clamps to the front pillar RH.

    5. B002C3P

      Connect the connector and attach the 3 clamps to the rear pillar LH.

    6. w/ Sliding Roof:


      1. B002B9T

        Connect the connector.

    7. w/ Camera Heater:


      1. B002BHN

        Connect the connector.

    8. w/ Pre-crash Safety System:


      1. B002BQE

        Connect the connectors.

    9. w/o Pre-crash Safety System:


      1. B002BW8

        Connect the connector.

    10. w/ Rain Sensor:


      1. B002BL3

        Connect the connector.

  8. INSTALL ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for both assist grip sub-assemblies.


    1. B002BR4

      Attach the clips to the assist grip as shown in the illustration.

    2. B002B7Y

      Attach the 2 clips to temporarily install the assist grip.

    3. Attach the 4 claws to install the 2 new assist grip covers and fix the assist grip in place.

  9. INSTALL REAR ASSIST GRIP ASSEMBLY LH

    B002BAX

    1. Attach the clips to the rear assist grip as shown in the illustration.

    2. B002BXA

      Attach the 2 clips to temporarily install the rear assist grip.

    3. Attach the 4 claws to install the 2 new assist grip covers and fix the rear assist grip in place.

  10. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL VISOR HOLDER

    Tech Tips

    Use the same procedure for both visor holders.


    1. Attach the 2 claws.

    2. Push in the visor holder to install it.

  12. INSTALL VISOR ASSEMBLY LH


    1. Install the visor assembly LH with the 2 screws.

    2. Attach the guide.

  13. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. INSTALL VISOR BRACKET COVER

    Tech Tips

    Use the same procedure for both visor bracket covers.


    1. Attach the 4 claws to install the visor bracket cover.

  15. INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  16. INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  17. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/o Pre-crash Safety System)

    Click here

  18. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  19. INSTALL SPOT LIGHT ASSEMBLY

    Click here

  20. INSTALL MAP LIGHT ASSEMBLY

    Click here

  21. INSTALL INNER ROOF SIDE GARNISH LH


    1. w/ Rear Sunshade:


      1. B002C0AE05
        Text in Illustration
        *1 End Of The Rear Window Shade Assembly
        *2 Guide

        Insert the rear window shade assembly and attach the 3 guides.

      2. Attach the 4 clips to install the inner roof side garnish LH.

        Note

        After installing the inner roof side garnish LH, make sure that the lip of the rear door opening trim weatherstrip LH is not pinched.

    2. w/o Rear Sunshade:


      1. Attach the 4 clips and 3 guides to install the inner roof side garnish LH.

        Note

        After installing the inner roof side garnish LH, make sure that the lip of the rear door opening trim weatherstrip LH is not pinched.

  22. INSTALL INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. INSTALL REAR SEAT SIDE GARNISH LH


    1. Attach the 4 claws and guide to install the rear seat side garnish LH.

      Note

      After installing the rear seat side garnish LH, make sure that the lip of the rear door opening trim weatherstrip LH is not pinched.

  24. INSTALL REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. INSTALL UPPER CENTER PILLAR GARNISH LH


    1. Pass the front seat outer belt floor anchor through the upper center pillar garnish LH.

    2. Attach the clip to install the upper center pillar garnish LH.

    3. Install the 2 screws.

      Note

      After installing the upper center pillar garnish LH, make sure that the lip of the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH is not pinched.

  26. INSTALL UPPER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. Attach the 5 clips and 2 guides.

    2. While pulling both sides of the lower center garnish outward by hand, set the garnish in place, and then attach the 2 claws to install the lower center pillar garnish LH.

      Note

      After installing the lower center pillar garnish LH, make sure that the lip of the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH is not pinched.

  28. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. INSTALL REAR DOOR SCUFF PLATE LH


    1. Attach the 10 claws and 3 clips to install the rear door scuff plate LH.

  30. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  31. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  32. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  33. INSTALL FRONT PILLAR GARNISH LH

    B002B7EE02

    1. Install the front pillar garnish clip A and front pillar garnish clip B to the front pillar garnish LH.

      Tech Tips

      Install the front pillar garnish clip A and front pillar garnish clip B so that it faces as shown in the illustration.

      Text in Illustration
      *1 Front Pillar Garnish Clip A
      *2 Front Pillar Garnish Clip B
    2. B002BFH

      Attach the guide.

    3. B002C30E02
      Text in Illustration
      *1 Front Pillar Garnish Clip A
      *2 Front Pillar Garnish Clip B

      Attach the front pillar garnish clip A and front pillar garnish clip B to install the front pillar garnish LH.

      Note

      After installing the front pillar garnish LH, make sure that the lip of the front door opening trim weatherstrip LH is not pinched.

  34. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  35. INSTALL FRONT DOOR OPENING TRIM COVER LH


    1. Attach the 5 claws to install the front door opening trim cover LH.

      Note

      After installing the front door opening trim cover LH, make sure that the lip of the front door opening trim weatherstrip LH is not pinched.

  36. INSTALL FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  37. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Attach the 10 claws and 4 clips to install the front door scuff plate LH.

  38. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. INSTALL REAR SEAT ASSEMBLY

    Click here

  40. INSTALL FRONT SEAT ASSEMBLY LH


    1. for Sports Seat Type:

      Click here

    2. for Luxury Seat Type:

      Click here

    3. for Standard Seat Type:

      Click here

  41. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  42. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  43. ENABLE AUTOAWAY/RETURN FUNCTION


    1. Restore the autoaway/return function setting to the previous condition by changing the customize parameter Click here.

  44. INSPECT FRONT POWER SEAT CONTROL SYSTEM


    1. for LHD:

      Click here

    2. for RHD:

      Click here

  45. INSPECT CLIMATE CONTROL SEAT SYSTEM

    Click here

  46. INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)

    Click here

  47. CHECK SRS WARNING LIGHT

    Click here

  48. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  49. INSTALL LUGGAGE COMPARTMENT FLOOR MAT

    Click here