CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
Tech Tips
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE
INSTALL FRONT SEAT ASSEMBLY
Place the front seat assembly in the cabin.
Note
2 or more people are required when inserting the front seat assembly into the vehicle.
Be careful not to damage the vehicle body.
Tech Tips
for Driver Side:
When placing the front seat assembly into the vehicle, pass it through under the steering wheel.
Tilt the front seat assembly to the rear of the vehicle.
Note
Be careful not to damage the front seat assembly and vehicle interior.
Attach the wire harness clamp.
Connect the connectors.
*1 | Connector Lock Lever |
*2 | CPA Upper Part |
*3 | CPA |
*a | Lock Position |
Connect the connector and push in the connector lock lever to the lock position.
Before connecting the side airbag connector, check that the position of the CPA is as shown in the illustration.
*1 | CPA | - | - |
*a | CORRECT | *b | INCORRECT |
Hold the sides of the CPA and push in the connector in the direction indicated by the arrow until a click sound is heard to connect the connector.
Note
Be careful not to damage the side airbag connector or wire harness.
When connecting the connector, make sure to push it straight in.
Do not hold any parts other than the CPA when connecting the connector.
If the upper portion of the CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the CPA. Therefore, hold the sides of the CPA.
Connect the connector.
Align the pin of the front seat adjuster with the hole in the vehicle.
Temporarily install the front seat assembly with the 4 bolts.
Connect the cable to the auxiliary battery negative (-) terminal.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
Operate the power seat switch assembly to move the front seat assembly to the rearmost position.
Tighten the 2 bolts in the order shown in the illustration.
Operate the power seat switch assembly to move the front seat assembly to the foremost position.
Tighten the 2 bolts in the order shown in the illustration.
INSTALL OUTER SEAT TRACK BRACKET COVER LH
Attach the 2 hooks and 2 claws to install the outer seat track bracket cover LH.
INSTALL INNER SEAT TRACK BRACKET COVER LH
Attach the 2 hooks and 2 claws to install the inner seat track bracket cover LH.
INSTALL FRONT SEAT INNER TRACK BRACKET COVER LH
Operate the power seat switch assembly to move the front seat assembly to the rearmost position.
Attach the 2 guides to install the front seat inner track bracket cover LH.
Attach the 2 hooks and 2 claws.
INSTALL FRONT SEAT OUTER TRACK BRACKET COVER LH
Attach the 2 guides to install the front seat outer track bracket cover LH.
Attach the 2 hooks and 2 claws.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Operate the power seat switch assembly and move the front seat assembly so that the nut for the anchor of the front seat outer belt assembly LH can be installed.
*1 | Protruding Part |
Connect the anchor of the front seat outer belt assembly LH with the nut.
Note
Do not allow the anchor of the front seat outer belt assembly LH to overlap the protruding part of the front seat assembly.
INSTALL SEAT BELT ANCHOR COVER CAP LH
Attach the 6 hooks to install the seat belt anchor cover cap LH.
INSTALL FRONT SEAT HEADREST ASSEMBLY
Install the front seat headrest assembly.
CHECK SRS WARNING LIGHT
INSPECT SEAT BELT WARNING SYSTEM
PERFORM INITIALIZATION (w/ Memory)
Note
Under any of the following conditions, perform initialization of the position control ECU assembly.
for LHD: Click here
for RHD: Click here
The position control ECU assembly is replaced.
The power seat motor assembly is inspected or replaced.
The front seat adjuster is inspected or replaced.
The lumbar support adjuster assembly is inspected or replaced.
The front seatback support is inspected or replaced.
INSPECT POWER SEAT CONTROL SYSTEM
for LHD: Click here
for RHD: Click here
INSPECT SEAT HEATER SYSTEM
INSPECT CLIMATE CONTROL SEAT SYSTEM
ENABLE AUTOAWAY/RETURN FUNCTION (w/ Memory)
Restore the autoaway/return function setting to the previous condition by changing the customize parameter Click here.
INSTALL LUGGAGE COMPARTMENT TRIM COVER LH
INSTALL LUGGAGE COMPARTMENT FLOOR MAT