Click here

POP UP HOOD LIFTER(for Front Side) REMOVAL

Click here
Click here Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the pop up hood lifter assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Mono Camera type:

Click here

for Stereo Camera type:

Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic View Monitor System

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
Front bumper assembly (Including removal and installation)

  • Ultrasonic sensor detection angle

  • Ultrasonic sensor detection angle registration

 Parking support brake system

Click here
Front television camera view adjustment Panoramic view monitor system

Click here
*: When performing learning using the GTS. Click hereClick here
CAUTION:

If the hood release lever is pulled after the pop up hood lifter assembly is activated, the hood may rise more.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:
    B004U54

    Be sure to read precaution thoroughly before servicing.

    Click here

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:
    B004UM0

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the pedestrian protection system.

    • If the pop up hood lifter deploys for any reason, it may cause a serious accident.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. Click here

    REMOVE HEADLIGHT ASSEMBLY LH (for LH Side)

    Click here

  5. Click here

    REMOVE HEADLIGHT ASSEMBLY RH (for RH Side)

    Tip:

    Use the same procedure for the LH side.

    Click here

  6. Click here

    REMOVE FRONT AIRBAG SENSOR LH (for LH Side)

    Click here

  7. Click here

    REMOVE FRONT AIRBAG SENSOR RH (for RH Side)

    Tip:

    Use the same procedure for the LH side.

    Click here

  8. Click here

    REMOVE POP UP HOOD LIFTER ASSEMBLY LH

    CAUTION:
    B004SHXC01
    B004VGX Extended Section

    • When storing the pop up hood lifter assembly LH even temporarily, be sure to keep the extended section side facing upward.

    • If the pop up hood lifter deploys for any reason, it may cause a serious accident.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the pedestrian protection system.

      • If the pop up hood lifter deploys for any reason, it may cause a serious accident.

    3. Disconnect pop up hood lifter connector.

      Note:

      When disconnecting pop up hood lifter connector, take care not to damage the wire harness.


      1. B004ROFC01
        *a Housing Lock
        *b CPA
        *c CPA Upper Part
        B004RMI Slide

        Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note:

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter connector.

      3. B004UIXC07
        *a Correct *b Incorrect
        *c CPA *d Housing

        After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

    4. B004RGW

      Remove the 3 bolts.

    5. Lift up the pop up hood lifter assembly LH to detach the hook and remove it.

    6. B004VV2

      While avoiding the air conditioning hose, pull out the pop up hood lifter assembly LH as shown in the illustration.

  9. Click here

    REMOVE POP UP HOOD LIFTER ASSEMBLY RH

    CAUTION:
    B004SHXC01
    B004VGX Extended Section

    • When storing the pop up hood lifter assembly RH even temporarily, be sure to keep the extended section side facing upward.

    • If the pop up hood lifter deploys for any reason, it may cause a serious accident.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the pedestrian protection system.

      • If the pop up hood lifter deploys for any reason, it may cause a serious accident.

    3. B004ROFC01
      *a Housing Lock
      *b CPA
      *c CPA Upper Part
      B004RMI Slide

      Disconnect pop up hood lifter connector.

      Note:

      When disconnecting pop up hood lifter connector, take care not to damage the wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note:

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter connector.

      3. B004UIXC07
        *a Correct *b Incorrect
        *c CPA *d Housing

        After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

    4. B004Y22

      Remove the 3 bolts.

    5. Lift up the pop up hood lifter assembly RH to detach the hook and remove it.

    6. B004TE3C01
      B004RMI Detach Hood Lock Control assembly Cable Clamp in this Direction
      B004T3S Disconnect Hood Lock Control assembly Cable End in this Direction

      Detach the hood lock control cable clamp.

    7. Disconnect the hood lock control cable end.

  10. Click here

    REMOVE HOOD LOCK ASSEMBLY

    Click here

  11. Click here

    REMOVE HOOD LOCK CONTROL CABLE COVER RH (for RHD)

    Click here

  12. Click here

    REMOVE HOOD LOCK CONTROL ASSEMBLY


    1. B004RB1C01
      B004RMI Remove in this Direction

      Pull out the hood lock control assembly to remove it.