KNEE AIRBAG ASSEMBLY(for Front Passenger Side)

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the lower No. 2 instrument panel airbag assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system (for Mono camera type)	for Mono Camera type: Click here for Stereo Camera type: Click here
		Lane control system (for Stereo camera type)
		Parking support brake system*
		Pre-collision system (for Mono camera type)
		Pre-collision system (for Stereo camera type)
		Adaptive high beam system
		Lighting system (EXT) cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic View Monitor System	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here

*: When performing learning using the GTS. Click hereClick here

Tip:

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

Click here

PROCEDURE

Click here
PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

Note:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Note:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
Click here
REMOVE FRONT DOOR SCUFF PLATE RH

Tip:
Use the same procedure for the LH side.

Click here
Click here
REMOVE COWL SIDE TRIM BOARD RH

Tip:
Use the same procedure for the LH side.

Click here
Click here
REMOVE INSTRUMENT SIDE PANEL RH

Click here
Click here
REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here
Click here
REMOVE NO. 2 CONSOLE UPPER PANEL GARNISH

Click here

Click here

REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:

Deployment Side

When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.

Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Remove the 2 bolts.

	Place Hands Here
	Remove in this Direction

Place your hand in the position shown in the illustration (A) and pull the lower No. 2 instrument panel airbag assembly toward the rear of the vehicle to detach the claw.

Place your hand in the gap (B), pull the lower No. 2 instrument panel airbag assembly toward the rear of the vehicle to detach the claw, and then remove the No. 2 lower instrument panel airbag assembly.

*a	Lock Button
	Release in this Direction
	Protective Tape

While holding the lower No. 2 instrument panel airbag assembly with one hand, use a thin-bladed screwdriver, release the lock button and disconnect the airbag connector.

Tip:

Tape the screwdriver tip before use.

KNEE AIRBAG ASSEMBLY(for Front Passenger Side) REMOVAL