Click here

KNEE AIRBAG ASSEMBLY(for Driver Side) REMOVAL

Click here
Click here Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Mono Camera type:

Click here

for Stereo Camera type:

Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic View Monitor System

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
*: When performing learning using the GTS. Click hereClick here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:
    B004U54

    Be sure to read precaution thoroughly before servicing.

    Click here

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:
    B004UM0

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. Click here

    REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  5. Click here

    REMOVE COWL SIDE TRIM BOARD LH

    Click here

  6. Click here

    REMOVE INSTRUMENT SIDE PANEL LH

    Click here

  7. Click here

    REMOVE LOWER NO. 1 INSTRUMENT PANEL PAD SUB-ASSEMBLY

    Click here

  8. Click here

    REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

  9. Click here

    REMOVE NO. 1 CONSOLE UPPER PANEL GARNISH

    Click here

  10. Click here

    REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:
    B004V4FC01
    B004VGX Deployment Side

    • When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

    • If the airbag deploys for any reason, it may cause a serious accident.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    3. B004R5B

      Remove the 4 bolts.

    4. B004SIFC01
      B004V32 Place Hands Here
      B004RMI Remove in this Direction

      Place your hand at the location shown in the illustration and pull the lower No. 1 instrument panel airbag assembly toward the rear of the vehicle to detach the claw to remove it.

    5. While holding the lower No. 1 instrument panel airbag assembly with one hand, perform the following procedure.


      1. B004ST2C01
        B004RMI Push and release the lock
        B004T3S Pull Out

        Detach the wire harness clamp.

      2. Detach the claw and disconnect the DLC3.

      3. Move the lock of the hood lock control lever in the direction indicated by the black arrow to release it, and then pull it out in the direction indicated by the white arrow.

      4. B004VN3C01
        *a Lock Button
        B004RMI Release in this Direction
        B004VGX Protective Tape

        Using a screwdriver, release the lock button and disconnect the airbag connector.

        Note:

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.

        Tip:

        Tape the screwdriver tip before use.