REAR SUSPENSION MEMBER INSTALLATION

PROCEDURE


  1. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for LH Side)


    1. B004U4PC01
      B004SZX Diluted Liquid Soap
      B004UK4 Front of the Vehicle

      Apply diluted liquid soap to the outside of a new rear suspension member rear body mounting cushion.

      Note

      Do not use grease or undiluted liquid soap. Doing so may cause the rear suspension member front body mounting cushion to slip out.

      Tech Tips

      A 20% liquid soap and water concentration is recommended.

    2. Temporarily install the rear suspension member rear body mounting cushion while confirming the installation direction.

    3. B004V0LN03

      Using SST, install the rear suspension member rear body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mounting cushion.

      SST
      09316-12010
      09570-24011
      09950-40011   ( 09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011 )
      09950-60021   ( 09951-00910 )

      Note

      Apply grease to the threads and tip of the SST center bolt before use.

  2. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  3. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION LH


    1. B004TONC02
      *A for LH Side
      *B for RH Side
      B004SZX Diluted Liquid Soap
      B004UK4 Front of the Vehicle

      Apply diluted liquid soap to the outside of a new rear suspension member front body mounting cushion.

      Note

      Do not use grease or undiluted liquid soap. Doing so may cause the rear suspension member front body mounting cushion to slip out.

      Tech Tips

      A 20% liquid soap and water concentration is recommended.

    2. Temporarily install the rear suspension member front body mounting cushion while confirming the installation direction.

    3. B004WRDN05

      Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

      SST
      09316-12010
      09570-24011
      09950-40011   ( 09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011 )
      09950-60021   ( 09951-00910 )

      Note

      Apply grease to the threads and tip of the SST center bolt before use.

  4. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION RH

    Tech Tips

    Perform the same procedure as for the LH side.

  5. INSTALL REAR SUSPENSION MEMBER REAR UPPER STOPPER


    1. Install the 2 rear suspension member rear upper stoppers to the rear suspension member sub-assembly.

  6. INSTALL REAR SUSPENSION MEMBER FRONT UPPER STOPPER


    1. Install the 2 rear suspension member front upper stoppers to the rear suspension member sub-assembly.

  7. INSTALL NO.4 EXHAUST PIPE SUPPORT BRACKET


    1. B004VB7

      Install the No.4 exhaust pipe support bracket to the rear suspension member sub-assembly with the 2 bolts.

      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

  8. INSTALL NO.5 EXHAUST PIPE SUPPORT BRACKET

    Tech Tips

    Perform the same procedure as for the No.4 exhaust pipe support bracket.

  9. TEMPORARILY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY LH (w/o Dynamic Rear Steering)


    1. B004YV8

      Insert the rear suspension toe adjust cam sub-assembly from the front of the vehicle. Then temporarily tighten the rear No. 2 suspension toe adjust plate and toe control link sub-assembly LH with the nut.

    2. B004UTSC01
      *a Matchmark

      Align the matchmarks on the rear suspension toe adjust cam sub-assembly, rear No. 2 suspension toe adjust plate and rear suspension member sub-assembly.

  10. TEMPORARILY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY RH (w/o Dynamic Rear Steering)

    Tech Tips

    Perform the same procedure as for the LH side.

  11. TEMPORARILY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH


    1. B004RFYC01
      B004SZX Bolt
      B004UK4 Nut

      Insert the bolt from the front of the vehicle. Then temporarily tighten the rear upper control arm assembly LH with the nut and washer.

  12. TEMPORARILY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  13. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. B004VJFC01
      B004SZX Bolt
      B004UK4 Nut

      Insert the bolt from the back of the vehicle. Then temporarily tighten the rear No. 1 suspension arm assembly LH with the nut and washer.

  14. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  15. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. B004W8Q

      Insert the rear suspension arm attachment sub-assembly from the back of the vehicle. Then temporarily tighten the rear No. 2 suspension toe adjust plate and rear No. 2 suspension arm assembly LH with the nut.

  16. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  17. TEMPORARILY TIGHTEN LOWER CONTROL ARM ASSEMBLY LH


    1. B004UARC01
      B004SZX Bolt
      B004UK4 Nut

      Insert the bolt from the back of the vehicle. Then temporarily tighten the lower control arm assembly LH with the nut.

  18. TEMPORARILY TIGHTEN LOWER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  19. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

    Click here

  20. INSTALL REAR STABILIZER BAR

    Click here

  21. INSTALL PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET

    Click here

  22. TEMPORARILY TIGHTEN REAR STABILIZER LINK ASSEMBLY LH

    Click here

  23. TEMPORARILY TIGHTEN REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  24. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. B004S0OC02
      *a Attachment
      *b Engine Lifter
      B004VGX Attachment placement location

      Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

      CAUTION:


      • The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

      • If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.

      B004XET

      Note

      Use attachments to keep the rear suspension member sub-assembly level.

    2. Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle body.

      Note

      When raising the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.

    3. Install the rear lower suspension member stopper LH, rear lower suspension member stopper RH, 2 rear lower suspension member stoppers and rear suspension member sub-assembly with the 8 bolts.

      Torque:
      Bolt A
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }
      Bolt B
      135 N*m  { 1377 kgf*cm, 100 ft.*lbf }

  25. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

    Click here

  26. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  27. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY


  28. STABILIZE SUSPENSION

    Click here

  29. FULLY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY LH (w/o Dynamic Rear Steering)

    Click here

  30. FULLY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY RH (w/o Dynamic Rear Steering)

    Tech Tips

    Perform the same procedure as for the LH side.

  31. FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

    Click here

  32. FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  33. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  34. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  35. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  36. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  37. FULLY TIGHTEN LOWER CONTROL ARM ASSEMBLY LH

    Click here

  38. FULLY TIGHTEN LOWER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  39. FULLY TIGHTEN REAR STABILIZER LINK ASSEMBLY LH

    Click here

  40. FULLY TIGHTEN REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  41. INSPECT TOE CONTROL LINK SUB-ASSEMBLY LH (w/o Dynamic Rear Steering)

    Click here

  42. INSPECT TOE CONTROL LINK SUB-ASSEMBLY RH (w/o Dynamic Rear Steering)

    Tech Tips

    Perform the same procedure as for the LH side.

  43. INSPECT REAR UPPER CONTROL ARM ASSEMBLY LH

    Click here

  44. INSPECT REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  45. INSPECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  46. INSPECT REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  47. INSPECT LOWER CONTROL ARM ASSEMBLY LH

    Click here

  48. INSPECT LOWER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  49. CONNECT PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET


    1. B004W3HC01
      *a Grommet
      *b Outside of Vehicle
      *c Inside of Vehicle

      Pass the connector through the hole to the inside of the vehicle and install the grommet of the parking brake actuator harness.

    2. Connect the connector.

    3. B004TLS

      Install the parking brake with bracket actuator assembly with the 2 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  50. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH

    Click here

  51. INSTALL REAR FLOOR FINISH PLATE

    Click here

  52. INSTALL ROPE HOOK ASSEMBLY

    Click here

  53. INSTALL REAR LUGGAGE COMPARTMENT TRIM COVER

    Click here

  54. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  55. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear Air Conditioning System)

    Click here

  56. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/ Rear Air Conditioning System)

    Tech Tips

    Use the same procedure described for the front luggage compartment trim cover (w/o Rear Air Conditioning System).

  57. INSTALL INNER LOWER LUGGAGE COMPARTMENT TRIM COVER

    Click here

  58. INSTALL TOOL BOX

    Click here

  59. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  60. INSTALL LUGGAGE COMPARTMENT TRIM COVER RH

    Click here

  61. INSTALL LUGGAGE COMPARTMENT FLOOR MAT

    Click here

  62. ADJUST PARKING BRAKE

    Click here

  63. INSTALL REAR WHEEL HOUSE LINER LH

    Tech Tips

    Use the same procedure for the RH and LH sides.

    Click here

  64. INSTALL ROCKER PANEL MOULDING PROTECTOR LH

    Click here

  65. INSTALL REAR WHEEL

    Click here

  66. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  67. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  68. PARKING LOCK

    Click here

  69. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  70. INSPECT AND ADJUST VEHICLE HEIGHT (w/ Air Suspension)

    Click here

  71. CHECK FOR SPEED SENSOR SIGNAL

    Click here

  72. PERFORM INITIALIZATION

    Electric parking brake system

    Click here

    Parking support brake system

    Click here

    Panoramic view monitor system

    Click here

    Parking assist monitor system

    Click here


      w/ Dynamic Rear Steering System:

    • Dynamic rear steering system

    Click here


      w/o Air Suspension System:

    • Automatic headlight beam level control system

    Click here

  73. ADJUST HEADLIGHT AIMING

    Click here

  74. PERFORM PARKING BRAKE SHOE BEDDING

    Click here