REAR PNEUMATIC CYLINDER INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. Click here

   TEMPORARILY TIGHTEN REAR PNEUMATIC CYLINDER WITH SHOCK ABSORBER ASSEMBLY LH

   
   

   1. When reusing the rear pneumatic cylinder with shock absorber assembly LH:

      
      

      1. Install 2 new O-rings, a new plate and new No. 2 connector to the front pneumatic cylinder with shock absorber assembly LH.

         Click here

   2. 

      Temporarily tighten the washer and rear pneumatic cylinder with shock absorber assembly LH with a new nut.

   3. 

      Temporarily tighten the rear pneumatic cylinder with shock absorber assembly LH with the 3 nuts.

      Tip:

      If the nut is hard to see, use a mirror.

2. Click here

   CONNECT NO.7 HEIGHT CONTROL TUBE

   
   
   1. 

      Connect the No. 7 height control tube to the rear pneumatic cylinder with shock absorber assembly LH.

      Click here

3. Click here

   CONNECT SKID CONTROL SENSOR WIRE LH

   
   
   1. 

      Install the skid control sensor wire LH with the nut.

      6.0 N*m

      61 kgf*cm

      53 in.*lbf

   2. Connect the connector.

4. Click here

   TEMPORARILY TIGHTEN REAR STABILIZER LINK ASSEMBLY LH

   Click here

5. Click here

   AIR MOVEMENT (WHEN REPLACING A REAR PNEUMATIC CYLINDER)

   Tip:

   Move the air pressure according to the instructions on the GTS.

   Click here

6. Click here

   AIR MOVEMENT (WHEN REPLACING THE 2 REAR PNEUMATIC CYLINDERS)

   Tip:

   Move the air pressure according to the instructions on the GTS.

   Click here

7. Click here

   STABILIZE SUSPENSION

   Click here

8. Click here

   TIGHTEN REAR PNEUMATIC CYLINDER WITH SHOCK ABSORBER ASSEMBLY LH

   
   
   1. 

      Fully tighten the nut.

      110 N*m

      1122 kgf*cm

      81 ft.*lbf

   2. 

      *a	Torque Wrench Fulcrum Length

      Fully tighten the 2 nuts A.

      40 N*m

      408 kgf*cm

      30 ft.*lbf

      Tip:

      If the nut is hard to see, use a mirror.

   3. Using SST, fully tighten the nut B.

      09249-37010

      Specified tightening torque
      40 N*m	408 kgf*cm	30 ft.*lbf

      Tip:
      

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using SST (fulcrum length of 100 mm (3.937 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 25.7 N*m (262 kgf*cm, 19 ft.*lbf)

      • If the nut is hard to see, use a mirror.

9. Click here

   INSTALL REAR SHOCK ABSORBER CAP LH

   Click here

10. Click here

    TIGHTEN REAR STABILIZER LINK ASSEMBLY LH

    Click here

11. Click here

    CHECK CONNECTIONS OF TUBES FOR AIR LEAKAGE

    
    

    1. Install the rear wheel RH.

       Click here

    2. Check the connections of the tubes for air leakage.

       Click here

    3. Remove the rear wheel RH.

       Click here

12. Click here

    INSTALL REAR WHEEL HOUSE LINER LH

    Tip:

    Use the same procedure for the RH and LH sides.

    Click here

13. Click here

    INSTALL ROCKER PANEL MOULDING PROTECTOR LH

    Click here

14. Click here

    INSTALL REAR WHEEL

    Click here

15. Click here

    INSTALL PACKAGE TRAY TRIM SIDE COVER LH

    Click here

16. Click here

    INSTALL NO. 1 CENTER SPEAKER GRILLE SUB-ASSEMEBLY

    Click here

17. Click here

    INSTALL PACKAGE TRAY TRIM GARNISH LH

    Click here

18. Click here

    INSTALL PACKAGE TRAY TRIM GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

19. Click here

    INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

20. Click here

    INSPECT AND ADJUST VEHICLE HEIGHT

    Click here

21. Click here

    CHECK HEIGHT CHANGE OPERATION

    Click here

22. Click here

    PERFORM INITIALIZATION

    Parking support brake system	Click here
    Panoramic view monitor system	Click here
    Parking assist monitor system	Click here
    w/ Dynamic Rear Steering System: Dynamic rear steering system	Click here

23. Click here

    ADJUST HEADLIGHT AIMING

    Click here