Click here

INSTRUMENT PANEL SAFETY PAD REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the instrument panel safety pad sub-assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type:Click here

for Mono Camera type:Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic view monitor system

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
Steering sensor (Including removal and installation) Steering angle neutral point Parking support brake system

Click here
Parking assist monitor system

Click here
Panoramic view monitor system

Click here
Steering angle setting Parking assist monitor system

Click here
Panoramic view monitor system

Click here
*: When performing learning using the GTS. Click hereClick here
Tip:

  • Use the same procedure as for the LHD and RHD vehicles.

  • The procedure listed below is for the LHD vehicles.

Click here

PROCEDURE


  1. Click here

    BOLT, SCREW AND NUT TABLE

    Tip:

    All bolts, nuts and clips relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.

  2. Click here

    PRECAUTION

    CAUTION:
    B004U54

    Be sure to read precaution thoroughly before servicing.

    Click here

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  3. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  4. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:

    • B004UM0

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  5. Click here

    REMOVE CONSOLE BOX ASSEMBLY

    Click here

  6. Click here

    REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  7. Click here

    REMOVE COWL SIDE TRIM BOARD LH


    1. B004SHVC01
      *1 Cap nut

      Remove the cap nut.

    2. Pull in the direction of the arrow in the illustration and detach the clamp and remove the cowl side trim board LH.

  8. Click here

    REMOVE INSTRUMENT SIDE PANEL LH


    1. B004ULBC01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration, detach the clip in the removal order and remove the instrument side panel LH.

  9. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure described for the LH side.

    Click here

  10. Click here

    REMOVE COWL SIDE TRIM BOARD RH

    Tip:

    Use the same procedure described for the LH side.

  11. Click here

    REMOVE INSTRUMENT SIDE PANEL RH


    1. B004Y86C01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration, detach the clip in the removal order and remove the instrument side panel RH.

  12. Click here

    REMOVE LOWER NO. 1 INSTRUMENT PANEL PAD SUB-ASSEMBLY


    1. B004TNIC01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration and detach the claw and clip.

    2. B004RXHC01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration, detach the clip and remove the No. 1 lower instrument panel pad sub-assembly.

    3. B004SCTC01
      *A w/ Combination Switch

      Disconnect the 3 connectors.

    4. w/ Combination Switch:


      1. Disconnect the connector.

  13. Click here

    REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B004TCMC01
      B004SZX Screw <A> or <B>

      Remove the 2 screws <A> or <B>.

    2. B004X7GC01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.

    3. B004RPYC01
      B004RMI Remove in this Direction

      Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the No. 1 instrument panel under cover sub-assembly.

    4. B004T3E

      Disconnect the connector.

  14. Click here

    REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  15. Click here

    REMOVE NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. w/ Headup Display:


      1. B004SHYC01
        B004V32 Place hand here
        B004RMI Remove in this Direction

        Place your hand at the position shown in the illustration and push in the direction indicated by the arrow to detach the clip.

      2. B004Y7SC01
        B004RMI Remove in this Direction

        Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the No. 2 instrument panel safety pad sub-assembly.

    2. w/o Headup Display:


      1. B004TYUC01
        B004V32 Place hand here
        B004RMI Remove in this Direction

        Place your hand at the position shown in the illustration and push in the direction indicated by the arrow to detach the clip.

      2. B004XFJC01
        B004RMI Remove in this Direction

        Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the No. 2 instrument panel safety pad sub-assembly.

    3. B004RPW

      Detach the clamp and disconnect the 2 connectors.

  16. Click here

    REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD


    1. B004TRMC01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and remove the No. 1 instrument panel safety pad together with the No. 1 instrument cluster moulding.

  17. Click here

    REMOVE NO. 1 INSTRUMENT CLUSTER MOULDING


    1. B004YR9

      Detach the clip and remove the No. 1 instrument panel safety pad from the No. 1 instrument cluster moulding.

  18. Click here

    REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B004W8A

      Remove the screw.

    2. B004V8WC01
      B004RMIC50 Remove in this Direction

      Pull in the direction indicated by the arrow shown in the illustration to detach the clip and remove the No. 1 instrument panel safety pad sub-assembly.

    3. B004YLU

      Disconnect the connector.

    4. B004SXKC01
      B004RMI Remove in this Direction

      Pull in the direction indicated by the arrow shown in the illustration to detach the clip and remove the No. 1 instrument panel register assembly.

  19. Click here

    REMOVE INSTRUMENT PANEL SAFETY PAD INSERT SUB-ASSEMBLY


    1. B004UDEC01
      B004V32 Place hand here

      Place your hand at the position shown in the illustration and detach the clip.

    2. B004VLYC01
      B004RMI Remove in this Direction - -

      Place your hand in the gap, and then, while pulling in the direction indicated by the arrow shown in the illustration, detach the guide and clip in the order shown in the illustration and remove the instrument panel safety pad insert sub-assembly.

  20. Click here

    REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. B004RKRC01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.

    2. B004T03C01
      B004RMI Remove in this Direction - -

      Place your hand in the gap, and then, while pulling in the direction indicated by the arrow shown in the illustration, detach the clip in the order shown in the illustration.

    3. B004VT4C01
      B004RMI Remove in this Direction

      Detach the clip in the order shown in the illustration and remove the lower instrument panel finish panel assembly.

    4. B004VYE

      Disconnect the 2 connectors.

  21. Click here

    REMOVE AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  22. Click here

    REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY


    1. B004VAVC01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.

    2. B004R24C01
      B004RMI Remove in this Direction - -

      Place your hand in the gap, and then, while pulling in the direction indicated by the arrow shown in the illustration, detach the clip in the order shown in the illustration.

    3. B004XK6

      Disconnect the connector.

  23. Click here

    REMOVE STEERING WHEEL SWITCH HOUSING

    Click here

  24. Click here

    REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. except Sport Package, w/ Illumination:


      1. B004REE

        Disconnect the connector.

    2. B004Y19C01
      B004V32 Place hands here
      B004RMI Remove in this Direction

      Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and remove the instrument cluster finish panel assembly.

    3. B004URK

      Disconnect the connector.

  25. Click here

    REMOVE COMBINATION METER ASSEMBLY

    Click here

  26. Click here

    REMOVE MULTI-DISPLAY ASSEMBLY

    Click here

  27. Click here

    REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B004XW8C01
      B004RMI Place hand here

      Pull in the direction indicated by the arrow shown in the illustration to detach the clip.

    2. B004U05C01
      B004RMI Remove in this Direction

      Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the No. 2 instrument panel under cover sub-assembly.

    3. B004X2Z

      Disconnect the connector.

  28. Click here

    REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  29. Click here

    REMOVE GLOVE COMPARTMENT DOOR PAD PLATE


    1. Open the glove compartment door assembly.

    2. B004WNTC01
      B004RMI Remove in this Direction

      Pull in the direction indicated by the arrow shown in the illustration to detach the clip and remove the glove compartment door pad plate.

  30. Click here

    REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. B004VCVC01
      B004SZX Screw <A> or <B>

      Remove the 2 screws <A> or <B>.

    2. Close the glove compartment door assembly.

    3. Remove the 2 screws <A> or <B>.

    4. B004RPUC01
      B004V32 Place hands here
      B004RMI Remove in this Direction

      Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and remove the glove compartment door assembly.

    5. B004WOJ

      Detach the clamp and disconnect the 2 connectors.

  31. Click here

    REMOVE TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)

    Click here

  32. Click here

    REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B004WJZ

      Disconnect the connector.

    2. B004VVYC01
      B004V32 Place hands here
      B004RMI Remove in this Direction

      Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and remove the No. 2 instrument panel register assembly.

  33. Click here

    REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET

    Click here

  34. Click here

    REMOVE FRONT PILLAR GARNISH LH

    Click here

  35. Click here

    REMOVE FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  36. Click here

    REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B004WD5C01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration, detach the clip and remove the No. 2 instrument panel speaker panel sub-assembly.

  37. Click here

    REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

    Click here

  38. Click here

    REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B004T49C01
      B004V32 Place hand here
      B004RMI Remove in this Direction

      Place your hand at the position shown in the illustration, detach the clip and remove the No. 2 instrument panel speaker panel sub-assembly.

    2. B004XBR

      Disconnect the connector.

  39. Click here

    REMOVE FRONT NO. 3 SPEAKER ASSEMBLY

    Click here

  40. Click here

    REMOVE NO. 1 CONSOLE BOX DUCT


    1. B004UAT

      Remove the 2 clips.

    2. B004SR6C01
      B004RMI Remove in this Direction

      Lift in the direction indicated by the arrow shown in the illustration and remove the No. 1 console box duct.

  41. Click here

    REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY

    Click here

  42. Click here

    REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Disconnect airbag connector:


      1. B004X8VC02
        *a Housing Lock *b CPA
        *c Disconnect the connector lock - -

        Push down the housing lock and slide the CPA to release the lock.

        Note:

        Do not pull while holding the wire harness.

      2. With the housing lock pushed down again, slide the CPA to disconnect the airbag connector.

      3. B004UXWC03
        *a CORRECT *b INCORRECT
        *c CPA *d Housing

        After disconnecting the airbag connector, check that the CPA is positioned further back than the housing.

    2. B004T3TC01
      B004SZX Bolt <C>

      Remove the 2 bolts <C>.

    3. B004Y74

      Detach the clamp.

    4. B004W94

      Disconnect the connector and detach the clamp.

    5. B004YHQ

      Disconnect the connector.

    6. B004RSJ

      Detach the claw and remove the cooler thermistor (room temperature sensor).

    7. B004UT1C01
      B004SZX Bolt <E> B004UK4 Clip <D>
      B004XCB Nut <F> - -

      Remove the 2 clips <D>, 7 bolts <E> and nut <F>.

    8. B004V1MC01
      B004RMI Lift Up Direction B004SZX Defroster nozzle assembly status

      Lift in the direction indicated by the arrow shown in the illustration to detach the guide.

      Note:

      Lift the defroster nozzle assembly until it is completely removed.

    9. B004W9HC01
      B004RMI Remove in this Direction - -

      Pull in the direction indicated by the arrow shown in the illustration and remove the instrument panel safety pad sub-assembly.