BLACK OUT TAPE(for Front Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here


  • Door glass

  • Door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

    Click here

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  6. REMOVE DOOR ARMREST COVER

    Click here

  7. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  8. REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  10. REMOVE FRONT DOOR NO. 1 TRIM BRACKET

    Click here

  11. REMOVE FRONT DOOR SERVICE HOLE COVER

    Click here

  12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

    Click here

  13. REMOVE FRONT DOOR GLASS RUN

    Click here

  14. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

    Click here

  15. REMOVE FRONT DOOR FIX WINDOW GLASS

    Click here

  16. REMOVE UPPER DOOR FRAME GARNISH

    Click here

  17. DISCONNECT FRONT DOOR WEATHERSTRIP

    Click here

  18. REMOVE FRONT DOOR PANEL PROTECTOR

    Click here

  19. REMOVE FRONT DOOR VENT SEAL

    Click here

  20. REMOVE FRONT DOOR REAR OUTSIDE STRIPE

    Tech Tips

    When removing the front door rear outside stripe, heat the vehicle body and front door rear outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Front Door Rear Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B005MXIC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the front door rear outside stripe and vehicle body.

    2. B005NH4

      Pull back on one of the ends of the front door rear outside stripe to remove it.

      Tech Tips

      When pulling on the front door rear outside stripe, pull it parallel to the body.

  21. REMOVE FRONT DOOR STRIPE

    Tech Tips

    When removing the front door stripe, heat the vehicle body and front door stripe using a heat light.

    Heating Temperature
    Item Temperature
    Front Door Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B005MXIC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the front door stripe and vehicle body.

    2. B005O4V

      Pull back on one of the ends of the front door stripe to remove it.

      Tech Tips

      When pulling on the front door stripe, pull it parallel to the body.

  22. REMOVE NO. 1 BLACK OUT TAPE

    Tech Tips

    When removing the No. 1 black out tape, heat the vehicle body and No. 1 black out tape using a heat light.

    Heating Temperature
    Item Temperature
    No. 1 Black Out Tape and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B005MXIC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the No. 1 black out tape and vehicle body.

    2. B005NXB

      Pull back on one of the ends of the No. 1 black out tape to remove it.

      Tech Tips

      When pulling on the No. 1 black out tape, pull it parallel to the body.