INSTRUMENT PANEL SAFETY PAD REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel safety pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

Removal/installation of the spiral cable with sensor sub-assembly

  • Steering angle neutral point (Initialize parking assist monitor system)

  • Steering angle setting

 Parking assist monitor system (w/ Parallel Parking Assist Function)

Click here for Initialization

Click here for Calibration
Parking assist monitor system (w/o Parallel Parking Assist Function)

Click here for Initialization

Click here for Calibration
Steering angle neutral point (Initialize panoramic view monitor system) Panoramic view monitor system

Click here for Initialization

Click here for Calibration
Steering angle neutral point (Initialize intelligent clearance sonar system) Intelligent clearance sonar system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B005NS4

Click here

PROCEDURE


  1. PRECAUTION

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

    Click here

  3. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  4. REMOVE INSTRUMENT PANEL GARNISH LH


    1. B005LZ6C01
      B005OOA Remove in this Direction

      Using a moulding remover B, disengage the 8 clips to remove the instrument panel garnish LH as shown in the illustration.

  5. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  6. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. for LHD:


      1. B005LV9

        Remove the 2 screws <D>.

      2. B005M70C01
        B005OOA Remove in this Direction

        Disengage the 3 claws as shown in the illustration.

      3. B005NL8C01
        B005OOA Remove in this Direction

        Disengage the 2 guides as shown in the illustration.

      4. B005PFT

        Disengage the 2 claws to disconnect the DLC3 connector.

      5. Disconnect the connector.

      6. Disengage the clamp to remove the No. 1 instrument panel under cover sub-assembly.

    2. for RHD:


      1. B005MZ1

        Remove the 2 screws <D>.

      2. B005L6XC02
        B005OOA Remove in this Direction

        Disengage the 3 claws as shown in the illustration.

      3. B005MJXC02
        B005OOA Remove in this Direction

        Disengage the guide as shown in the illustration.

      4. B005N3F

        Disengage the 2 claws to disconnect the DLC3 connector.

      5. Disconnect the connector.

      6. Disengage the clamp to remove the No. 1 instrument panel under cover sub-assembly.

  8. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B005NQZ

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. for LHD:


      1. B005OJ7C01
        *a Protective Tape

        Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to disconnect the instrument panel hole cover.

      2. B005Q7J

        Remove the 2 screws <D>.

      3. B005NC7C01
        B005OOA Remove in this Direction

        Disengage the 11 clips and 3 claws as shown in the illustration.

    2. for RHD:


      1. B005LM4C02
        B005OOA Remove in this Direction

        Disengage the 12 clips and 3 claws as shown in the illustration.

    3. Disconnect each connector to remove the lower instrument panel finish panel sub-assembly.

  10. REMOVE LOWER INSTRUMENT FINISH PANEL SUB


    1. B005N54C01
      B005M6U Place Hand Here
      B005OOA Remove in this Direction
      B005NIZ Order of Removal

      Disengage the 3 clips and 4 guides as shown in the illustration.

    2. B005Q2BC01
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the 6 clips as shown in the illustration.

    3. Disconnect the connector to remove the lower instrument finish panel sub.

  11. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  12. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. B005LACC01
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the 4 clips as shown in the illustration.

    2. B005PF2C01
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the 3 clips as shown in the illustration.

    3. Disconnect the connector to remove the instrument cluster finish panel sub-assembly.

  13. REMOVE COMBINATION METER ASSEMBLY

    Click here

  14. REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR

    Click here

  15. REMOVE RADIO RECEIVER ASSEMBLY WITH REGISTER

    Click here

  16. REMOVE CONSOLE BOX ASSEMBLY


    1. B005NUB

      Disengage the clamp.

    2. B005Q4UC01
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the 5 clips as shown in the illustration.

    3. Disconnect each connector to remove the console box assembly.

  17. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for 12.3 Inch Display)


    1. B005MY6C02
      B005M97 Protective Tape

      Apply protective tape to the areas shown in the illustration.

    2. B005QC8C01
      B005M6U Insert Moulding Remover A Here
      B005OOA Remove in this Direction

      Using a moulding remover A, disengage the 3 clips as shown in the illustration.

    3. B005L3IC02
      B005OOA Remove in this Direction

      Disengage the 5 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.

  18. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 12.3 Inch Display)


    1. B005MO5C01
      B005M97 Protective Tape

      Apply protective tape to the areas shown in the illustration.

    2. B005QC4C01
      B005M6U Insert Moulding Remover A Here
      B005OOA Remove in this Direction

      Using a moulding remover A, disengage the 2 clips as shown in the illustration.

    3. B005Q4LC01
      B005M6U Insert Moulding Remover A Here
      B005OOA Remove in this Direction

      Using a moulding remover A, disengage the 5 claws, 4 clips and 7 guides to remove the instrument panel finish panel sub-assembly as shown in the illustration.

  19. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for 8 Inch Display)


    1. B005P76C01
      B005M97 Protective Tape

      Apply protective tape to the areas shown in the illustration.

    2. B005OPBC01
      B005M6U Insert Moulding Remover A Here
      B005OOA Remove in this Direction

      Using a moulding remover A, disengage the 3 clips, 2 claws and guide as shown in the illustration.

    3. B005L7FC01
      B005OOA Remove in this Direction

      Disengage the 5 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.

  20. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 8 Inch Display)


    1. B005LFEC01
      B005M97 Protective Tape

      Apply protective tape to the areas shown in the illustration.

    2. B005P4CC01
      B005M6U Insert Moulding Remover B Here
      B005OOA Remove in this Direction

      Using a moulding remover B, disengage the 2 clips as shown in the illustration.

    3. B005MZ2C01
      B005M6U Insert Moulding Remover A Here
      B005OOA Remove in this Direction

      Using a moulding remover A, disengage the claw, 5 clips and 4 guides to remove the instrument panel finish panel sub-assembly as shown in the illustration.

  21. REMOVE ACCESSORY METER ASSEMBLY (for 12.3 Inch Display)

    Click here

  22. REMOVE MULTI-DISPLAY ASSEMBLY (for 8 Inch Display)

    Click here

  23. REMOVE INSTRUMENT PANEL GARNISH RH


    1. B005L32C01
      B005OOA Remove in this Direction

      Using a moulding remover B, disengage the 8 clips as shown in the illustration.

    2. w/ Airbag Cut Off Switch:


      1. Disconnect the connector.

    3. Remove the instrument panel garnish RH.

  24. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  25. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  26. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B005OWK

      Remove the 2 screws <D>.

    2. B005NWQC01
      B005OOA Remove in this Direction

      Disengage the 2 claws as shown in the illustration.

    3. B005MH7C01
      B005OOA Remove in this Direction

      Disengage the 2 guides as shown in the illustration.

    4. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.

  27. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Open the glove compartment door assembly.

    2. B005O3Y

      Remove the 3 screws <E>.

    3. Close the glove compartment door assembly.

    4. B005OOD

      Remove the 2 bolts <B> or <C>.

    5. B005LBIC01
      B005OOA Remove in this Direction

      Disengage the 6 claws as shown in the illustration.

    6. Disconnect the connector.

    7. Disengage the clamp to remove the glove compartment door assembly.

  28. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B005MCVC02
      B005M97 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. B005O0QC02
      B005M6U Insert Moulding Remover B Here
      B005OOA Remove in this Direction

      Using a moulding remover B, disengage the 2 clips as shown in the illustration.

    3. B005PB4C02
      B005OOA Remove in this Direction

      Disengage the 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.

  29. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

    Click here

  30. REMOVE FRONT PILLAR GARNISH LH

    Click here

  31. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY


    1. B005LF8C01
      B005M97 Protective Tape

      Apply protective tape to the areas shown in the illustration.

    2. B005LD5C01
      B005M6U Insert Moulding Remover B Here
      B005OOA Remove in this Direction

      Using a moulding remover B, disengage the 2 clips as shown in the illustration.

    3. B005M06C01
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the 2 clips to remove the No. 1 speaker opening cover assembly as shown in the illustration.

  32. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY

    Click here

  33. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B005MQOC02
      B005M97 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. B005OBUC02
      B005M6U Insert Moulding Remover B Here
      B005OOA Remove in this Direction

      Using a moulding remover B, disengage the 2 clips as shown in the illustration.

    3. B005PV7C02
      B005OOA Remove in this Direction

      Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.

  34. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  35. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  36. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B005LWPC01
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.

  37. REMOVE NO. 2 INSTRUMENT CLUSTER MOULDING


    1. B005MOQC01
      B005OOA Remove in this Direction

      Using a moulding remover A, disengage the 2 clips as shown in the illustration.

    2. B005PSZC01
      B005M6U Place Hand Here
      B005OOA Remove in this Direction
      B005NIZ Order of Removal

      Disengage the 4 clips to remove the No. 2 instrument cluster moulding as shown in the illustration.

    3. w/ Interior Illumination:


      1. Disconnect the connector.

  38. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    1. B005MRC

      Using a clip remover, remove the clip.

    2. B005OEV

      Remove the 2 screws <E>.

    3. B005O7UC01
      B005OOA Remove in this Direction

      Disengage the 3 guides to remove the front No. 1 console box insert as shown in the illustration.

  39. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. B005QGN

      Using a clip remover, remove the clip.

    2. B005Q6W

      Remove the 4 screws <E>.

    3. B005LNDC01
      B005OOA Remove in this Direction

      Disengage the guide to remove the front No. 2 console box insert as shown in the illustration.

  40. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

    Click here

  41. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Disconnect each connector.

      B005M0DC01
      *A w/ Telematics Transceiver *B w/ Telematics Transceiver except G-BOOK

    2. Disengage each clamp.

    3. Remove the 2 clips.

      B005QEQC01
      *a Bolt <A> *b Bolt <C>
      *c Clip *d Nut <G>

    4. Remove the 7 bolts <C>, 2 bolts <A> and nut <G>.

    5. Disengage the 4 guides and remove the instrument panel safety pad sub-assembly as shown in the illustration.

      B005N00C01
      B005OOA Remove in this Direction - -

      Note


      • Do not damage the instrument panel safety pad sub-assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.