CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures after parts removed/installed/replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	for 8GR-FKS: Click here for V35A-FTS: Click here
	Memorize steering angle neutral point	LKA/LDA system	Click here
		Parking support brake system*
		Pre-collision system
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic View Monitor system	Click here
	Initialize Rear Door Sunshade System	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

PROCEDURE

PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 8GR-FKS:

Click here

for V35A-FTS:

Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE ROOF HEADLINING ASSEMBLY

Click here

REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

CAUTION:

Deployment Side

When storing the curtain shield airbag assembly LH, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.

Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.

*a	Lock Button
	Protective Tape
	Release in this Direction

Using a screwdriver, release the lock button and disconnect the airbag connector.

Note

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

Tech Tips

Tape the screwdriver tip before use.

Using needle-nose pliers, remove the pin from the clip A.

Tech Tips

Use the same procedure for the opposite side.
Using 2 thin bladed screwdrivers, detach the claw and remove the clip A.

Tech Tips

Use the same procedure for the opposite side.
Using a clip remover, detach the clip B.

Note

If the clip B has been removed, replace it with a new one.

Tech Tips

Tape the clip remover tip before use.
Detach the claw.
Remove the 4 bolts and deployment portion of the curtain shield airbag assembly LH.

Note

The bolt must not be reused.

Remove the 2 bolts and detach the hook to remove the curtain shield airbag assembly LH inflator.

Note

The bolt must not be reused.

*a	Clip A	*b	Clip B
	Remove in this Direction		Protective Tape