REAR DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door lock assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Disconnect cable from negative battery terminal	Memorize steering angle neutral point	LKA/LDA System	Click here
		Intelligent clearance sonar system*1
		Pre-crash safety system
		Lighting system (EXT) Cornering lights
		Adaptive high beam system
	Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes)	Stop and start system	Click here
	Memorize steering angle neutral point	Parking assist monitor system (w/ Parallel parking assist function)	Click here
		Parking assist monitor system (w/o Parallel parking assist function)	Click here
		Panoramic view monitor system	Click here
	Initialize back door lock	Power door lock control system	Click here
	Reset back door close position	Power back door system	Click here
Rear door glass sub-assembly Rear door glass run	Initialize Power Window Control System	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function	Click here

*1: When performing learning using the GTS.
Click here Click here

Tech Tips

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

PRECAUTION

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Click here
REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here
REMOVE REAR DOOR ARMREST COVER

Click here
REMOVE COURTESY LIGHT ASSEMBLY

Click here
REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here
REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Click here
REMOVE REAR DOOR NO. 2 TRIM BRACKET

Click here
REMOVE REAR DOOR SERVICE HOLE COVER

Click here
REMOVE REAR DOOR GLASS RUN

Click here
REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Click here
DISCONNECT REAR DOOR WEATHERSTRIP
1. Disconnect the rear door weatherstrip until the screws of the rear door rear guide seal is visible.
REMOVE REAR DOOR REAR GUIDE SEAL

Click here
REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here
REMOVE REAR DOOR LOCK ASSEMBLY
1. *a Release Plate
  
  Remove in this Direction
  
  Using a T30 "TORX" socket wrench, remove the 3 screws.
2. Move the rear door lock assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock assembly.
3. When reusing the rear door lock assembly:
  1. Remove the door lock wiring harness seal from the rear door lock assembly.
REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY
1. Using a screwdriver, disengage the 2 claws as shown in the illustration.
2. Remove in this Direction
  
  Disengage the 2 claws to remove the rear door lock cover sub-assembly as shown in the illustration.
REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
1. Remove in this Direction
  
  Remove the rear door lock remote control cable assembly as shown in the illustration.
REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
1. Remove in this Direction
  
  Remove the rear door inside locking cable assembly as shown in the illustration.

*a	Release Plate
	Remove in this Direction