TELEPHONE MICROPHONE ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the telephone microphone assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS: Click here

for V35A-FTS: Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here


  • Forward recognition camera

  • Windshield glass (Including removal and installation)

 Adjust forward recognition camera

  • Dynamic radar cruise control system

  • Forward recognition camera system

  • LKA/LDA system

  • Road sign assist system

  • Pre-collision system

  • Automatic high beam system

  • Adaptive high beam system

Click here

*: When performing learning using the GTS.
Click here Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    B006BC1

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Click here

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006BY6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE MAP LIGHT ASSEMBLY (for ERA-GLONASS)

    Click here

  5. REMOVE NO. 2 TELEPHONE MICROPHONE ASSEMBLY (for ERA-GLONASS)


    1. B006DBFC02
      B006AHR Screw
      B006EC9 Connector

      Remove the 2 screws.

    2. Detach the claw and clamp.

    3. Disconnect the connector.

    4. B006A0C

      Remove the 6 screws and the cover.

    5. B006A7V

      Remove the 4 screws.

    6. Detach the claw and then remove the theft warning ultrasonic sensor.

    7. B0069Y6

      Disconnect the connector.

    8. Detach the guides.

    9. Detach the claw and remove the No. 2 telephone microphone assembly.

  6. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  7. REMOVE TELEPHONE MICROPHONE ASSEMBLY (for Sliding Roof)


    1. for LHD:


      1. B006C38C03
        *A for 12 Speakers
        *B for 24 Speakers

        Disconnect the connector.

      2. Detach the claw and remove the telephone microphone assembly.

    2. for RHD:


      1. B006F3TC03
        *A for 12 Speakers
        *B for 24 Speakers

        Disconnect the connector.

      2. Detach the claw and remove the telephone microphone assembly.

  8. REMOVE TELEPHONE MICROPHONE ASSEMBLY (for Panoramic Moon Roof)


    1. B006CQUC01
      *A for 12 Speakers
      *B for 24 Speakers

      Disconnect the connector.

    2. Detach the claw and remove the telephone microphone assembly.