TELEMATICS TRANSCEIVER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the telematics transceiver removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS: Click here

for V35A-FTS: Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

Telematics transceiver assembly Register vehicle information Emergency call service

Click here

Mobile phone battery Reset mobilephone battery condition
*: When performing learning using the GTS.
Click here Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    Click here

    B006BC1

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Click here

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006BY6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE INSTRUMENT SIDE PANEL LH

    Click here

  5. REMOVE INSTRUMENT SIDE PANEL RH

    Click here

  6. REMOVE LOWER NO. 1 INSTRUMENT PANEL PAD SUB-ASSEMBLY

    Click here

  7. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

  8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    Click here

  9. REMOVE NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  10. REMOVE INSTRUMENT PANEL SAFETY PAD INSERT SUB-ASSEMBLY

    Click here

  11. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

    Click here

  12. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH

    Click here

  13. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  14. REMOVE GLOVE COMPARTMENT DOOR PAD PLATE

    Click here

  15. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

    Click here

  16. REMOVE TELEMATICS TRANSCEIVER


    1. for ERA-GLONASS:


      1. B006CAFC04
        B006AHR Bolt
        B006EC9 Connector
        B006FCW Nut

        Remove the bolt and nut.

      2. Detach the guide.

      3. Disconnect the 3 connectors and remove the telematics transceiver.

    2. for G-BOOK:


      1. B006GLUC04
        B006AHR Bolt
        B006EC9 Connector
        B006FCW Nut

        Remove the bolt and nut.

      2. Detach the guide.

      3. Disconnect the 4 connectors and remove the telematics transceiver.