SLIDING ROOF HOUSING(for Panoramic Moon Roof) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during sliding roof glass sub-assembly, sliding roof housing assembly, sliding roof drive gear assembly, sliding roof rail sub-assembly or sunshade trim sub-assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	for 8GR-FKS: Click here for V35A-FTS: Click here
	Memorize steering angle neutral point	LKA/LDA system	Click here
		Parking support brake system*
		Pre-collision system
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic View Monitor System	Click here
	Initialize Rear Door Sunshade System	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here
Sliding roof glass sub-assembly (Including removal and installation)	Initialize panoramic moon roof system	Auto operation function Jam protection function Key-off operation function Key-linked function Wireless transmitter-linked function Sliding roof open warning function may not operate Sliding roof may move in reverse or become misaligned	Click here
Sliding roof drive gear sub-assembly	Initialize panoramic moon roof system	Auto operation function Jam protection function Key-off operation function Key-linked function Wireless transmitter-linked function Sliding roof open warning function may not operate sliding roof may move in reverse or become misaligned	Click here
Sliding roof drive gear assembly (Including removal and installation)	Initialize roof sunshade system	Auto open and close function Jam protection function may not operate Roof sunshade may move in reverse or become misaligned	Click here
Sliding roof housing assembly (Including removal and installation)	Initialize panoramic moon roof system	Auto operation function Jam protection function Key-off operation function Key-linked function Wireless transmitter-linked function Sliding roof open warning function may not operate Sliding roof may move in reverse or become misaligned	Click here
Sliding roof housing sub-assembly (Including removal and installation) Sliding roof housing assembly (Including removal and installation)	Initialize roof sunshade system	Auto open and close function Jam protection function may not operate Roof sunshade may move in reverse or become misaligned	Click here
Slide roof rail sub-assembly (Including removal and installation)	Initialize panoramic moon roof system	Auto operation function Jam protection function Key-off operation function Key-linked function Wireless transmitter-linked function Sliding roof open warning function may not operate Sliding roof may move in reverse or become misaligned	Click here

*: When performing learning using the GTS.
Click here Click here

PROCEDURE

PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 8GR-FKS:

Click here

for V35A-FTS:

Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE SLIDING ROOF SIDE GARNISH LH
1. Move the sunshade trim sub-assembly to the fully opened position.
2. Remove the sliding roof side garnish LH.
REMOVE SLIDING ROOF SIDE GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE SLIDING ROOF SIDE GARNISH LH
1. Detach the claw and the sliding roof side garnish LH.
REMOVE SLIDING ROOF SIDE GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY
1. Move the sliding roof glass sub-assembly to the fully closed position.
2. Using a T25 "TORX" socket wrench, remove the 6 "TORX" screws and sliding roof glass sub-assembly.
  
  Note
  
  To prevent the sliding roof glass sub-assembly and sliding roof drive gear assembly from becoming misaligned, move the sliding roof glass sub-assembly to the fully closed position before removing.
REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

Click here
REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH
1. Bolt
  
  Nut
  
  Remove the bolt, 2 nuts and front sliding roof housing mounting bracket LH.
  
  Note
  
  If the removed nut is the same shape as that shown in the illustration, replace it the supplied replacement part.
REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE REMOVABLE ROOF BRACKET REINFORCEMENT LH
1. Bolt
  
  Nut
  
  Remove the 3 bolts, 3 nuts and removable roof bracket reinforcement LH.
REMOVE REMOVABLE ROOF BRACKET REINFORCEMENT RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE SLIDING ROOF HOUSING ASSEMBLY
1. Remove the 20 nuts.
  
  Note
  
  If the removed nut is the same shape as that shown in the illustration, replace it the supplied replacement part.

	Bolt
	Nut

	Bolt
	Nut