REAR SEAT ASSEMBLY(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS: Click here

for V35A-FTS: Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here


  • Position control ECU assembly LH (Including removal and installation)

  • Position control ECU assembly RH (Including removal and installation)

  • Rear seat headrest assembly LH (Including removal and installation)

  • Rear seat headrest assembly RH (Including removal and installation)

  • Rear No.1 seat adjuster assembly (Including removal and installation)

  • Rear No.2 seat adjuster assembly (Including removal and installation)

  • No.1 seat reclining adjuster assembly RH (Including removal and installation)

 Initialize position control ECU Rear power seat control system

Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B006C5U

Note


  • If the rear seat cushion airbag assembly LH was deployed, replace the rear seat cushion panel LH, rear seat cushion pad and separate type rear seat cushion cover with the necessary parts in accordance with the extent of the collision damage.

  • If the rear seat airbag assembly LH was deployed, replace the rear seat sub panel sub-assembly LH, separate type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    B006BC1

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      B006BY6

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here


      1. for 8GR-FKS:

        Click here

      2. for V35A-FTS:

        Click here

  4. REMOVE REAR SEAT CUSHION ASSEMBLY LH


    1. B006B4VC01
      B006BJ7 Place Hand Here
      B006DHE Remove in this Direction

      Place your hand in the position shown in the illustration and lift the rear seat cushion assembly LH in the removal direction and detach the hook.

      Note


      • Detach each hook individually.

      • When the hook is detached, replace the rear seat cushion lock hook with a new one.

    2. B006DYFC01
      B006EC9 Rear Seat Cushion Airbag Assembly LH Connector

      Detach the wire harness clamp and disconnect the connector.

    3. Disconnect the connector of the rear seat cushion airbag assembly LH.


      1. Push down the white housing lock and slide the yellow CPA.

        B006G4FC28
        *a Housing Lock *b CPA

        Note


        • Do not pull while holding the wire harness.

        • Do not try to release the lock while holding down the top of the CPA (A in the illustration), as this prevents the lock from being released.

      2. Slide the yellow CPA while pushing down the white housing lock again, and disconnect the connector.

    4. B006E67

      Using a clip remover, detach the clip.

    5. w/ Refresh Seat:


      1. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

        B0069N7C01
        B006DHE Remove in this Direction B006GBM Protective Tape

      2. Detach the tube clamp.

    6. Remove the rear seat cushion assembly LH.

      Note

      Do not damage the rear seat cushion assembly LH, body and body interior.

  5. REMOVE REAR SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE REAR CENTER SEAT CUSHION ASSEMBLY


    1. B006FM8

      Slide the rear center seat lap type belt assembly RH.

    2. B006D0ZC01
      B006BJ7 Place Hand Here
      B006DHE Remove in this Direction

      Place your hand in the position shown in the illustration and lift the rear center seat cushion assembly in the removal direction and detach the hook.

      Note

      When the hook is detached, replace the rear seat cushion lock hook with a new one.

    3. B006B6RC01
      B006DHE Remove in this Direction

      Pull in the removal direction shown in the illustration to detach the hook.

    4. B006H0S

      w/ Occupant Detection Sensor:


      1. Detach the wire harness clamp and disconnect the connector.

    5. Remove the rear center seat cushion assembly.

      Note

      Do not damage the rear center seat cushion assembly, body and body interior.

  7. REMOVE REAR SEAT CUSHION LOCK HOOK

    Note


    • If the rear seat cushion hook is detached, replace the rear seat cushion lock hook with a new one.

    • Do not reuse the rear seat cushion lock hook after removing it.

    Tech Tips

    Use the same procedure for the other side.


    1. B006DK3C04
      *a Body
      *b Sleeve

      Insert 2 thin-bladed screwdrivers between the rear seat cushion lock hook sleeve and body as shown in the illustration.

    2. Pull up the 2 thin-bladed screwdrivers to detach the claws and remove the rear seat cushion lock hook.

  8. REMOVE REAR SEATBACK ASSEMBLY LH


    1. B006D11C01
      B006GBM Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, remove the cap.

    2. B006CEYC01
      B006DHE Remove in this Direction
      B006GBM Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, press the button to release the lock and remove the belt band.

    3. B006FKGC01
      B006DHE Remove in this Direction

      Remove the bolt and floor anchor of the rear seat outer belt assembly LH.

    4. Remove the nut and floor anchor of the rear center seat outer belt assembly.

    5. B006C8MC01
      B006FCW Rear Seat Airbag Assembly LH Connector
      B0069MV Rear Seat Cushion Airbag Assembly LH Connector

      Remove the bolt and lift the connector holder.

    6. Disconnect the 2 connectors.

    7. Disconnect the connector of the rear seat airbag assembly LH.


      1. Push down the white housing lock and slide the yellow CPA.

        B006G4FC28
        *a Housing Lock *b CPA

        Note


        • Do not pull while holding the wire harness.

        • Do not try to release the lock while holding down the top of the CPA (A in the illustration), as this prevents the lock from being released.

      2. Slide the yellow CPA while pushing down the white housing lock again, and disconnect the connector.

    8. Disconnect the connector of the rear seat cushion airbag assembly LH.


      1. Slide the white slider and disconnect the connector.

        B0069S9C27
        *a Slider - -

        Note

        Do not pull while holding the wire harness.

    9. B006DV3

      Disconnect the 4 connectors.

    10. Detach the wire harness clamp.

    11. B006ERDC01
      B006DHE Remove in this Direction (1)
      B006B42 Remove in this Direction (2)

      Remove the 2 nuts.

    12. Pull in the removal direction (1) shown in the illustration and disconnect the rear seatback assembly LH from the rear No. 2 seat adjuster assembly.

    13. Lift in the removal direction (2) shown in the illustration and disconnect the rear seatback assembly LH from the No. 2 seat reclining adjuster assembly.

    14. B006EAI

      Using a clip remover, detach the clip and remove the rear seatback assembly LH.

      Note

      Do not damage the rear seatback assembly LH, body and body interior.

  9. REMOVE REAR SEATBACK ASSEMBLY RH


    1. B0069RBC01
      B006GBM Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, remove the cap.

    2. B0069G3C01
      B006DHE Remove in this Direction
      B006GBM Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, press the button to release the lock and remove the belt band.

    3. B006FX0C01
      B006DHE Remove in this Direction

      Remove the bolt and floor anchor of the rear seat outer belt assembly RH.

    4. B006G17C01
      B006FCW Rear Seat Airbag Assembly RH Connector
      B0069MV Rear Seat Cushion Airbag Assembly RH Connector

      Remove the bolt and lift the connector holder.

    5. Disconnect the 2 connectors.

    6. Disconnect the connector of the rear seat airbag assembly RH.


      1. Push down the white housing lock and slide the yellow CPA.

        B006G4FC28
        *a Housing Lock *b CPA

        Note


        • Do not pull while holding the wire harness.

        • Do not try to release the lock while holding down the top of the CPA (A in the illustration), as this prevents the lock from being released.

      2. Slide the yellow CPA while pushing down the white housing lock again, and disconnect the connector.

    7. Disconnect the connector of the rear seat cushion airbag assembly RH.


      1. Slide the white slider and disconnect the connector.

        B0069S9C27
        *a Slider - -

        Note

        Do not pull while holding the wire harness.

    8. B006C22C01
      *A w/ Ottoman

      w/o Ottoman:


      1. Disconnect the 4 connectors.

    9. w/ Ottoman:


      1. Disconnect the 5 connectors.

    10. Detach the wire harness clamp.

    11. B006G1HC01
      B006DHE Remove in this Direction (1)
      B006B42 Remove in this Direction (2)

      Remove the 2 nuts.

    12. Pull in the removal direction (1) shown in the illustration and disconnect the rear seatback assembly RH from the No. 1 rear seat adjuster assembly.

    13. Lift in the removal direction (2) shown in the illustration and disconnect the rear seatback assembly RH from the No. 1 seat reclining adjuster assembly.

    14. B006DE9

      Using a clip remover, detach the clip and remove rear seatback assembly RH.

      Note

      Do not damage the rear seatback assembly RH, body and body interior.

  10. REMOVE REAR CENTER SEAT ARMREST ASSEMBLY


    1. B006AUTC01
      *A w/ Rear Seat Entertainment System

      w/o Rear Seat Entertainment System:


      1. Disconnect the connector.

    2. w/ Rear Seat Entertainment System:


      1. Disconnect the 2 connectors.

    3. Detach the clamp and remove the connector holder.

    4. Remove the 2 bolts.

    5. B006BCV

      Using a clip remover, detach the clip and fold back the armrest cover.

    6. B006DZL

      Remove the 2 nuts and rear center seat armrest assembly.

      Note

      Do not damage the rear seat center armrest assembly, body and body interior.

  11. REMOVE REAR NO. 2 SEAT ADJUSTER ASSEMBLY


    1. B006FAKC03
      B006AHR Bolt
      B006EC9 Nut

      Remove the 3 bolts, nut and rear No. 2 seat adjuster assembly.

  12. REMOVE REAR NO. 1 SEAT ADJUSTER ASSEMBLY


    1. B006CG5C03
      B006AHR Connector
      B006EC9 Bolt
      B006FCWC03 Nut

      Disconnect the connector.

    2. Remove the 3 bolts, nut and rear No. 1 seat adjuster assembly.

  13. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  14. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. REMOVE REAR SEAT SIDE GARNISH LH

    Click here

  16. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE ROOM PARTITION BOARD ASSEMBLY LH


    1. B006D2IC01
      B006DHE Remove in this Direction

      Remove the nut.

    2. Pull in the removal direction shown in the illustration to detach the clip and claw.

    3. B006AQB

      Detach the claw and guide and remove the belt guides of the rear seat outer belt assembly LH and rear center seat outer belt assembly.

    4. B006EPEC01
      B006DHE Remove in this Direction

      Pull the rear seat outer belt assembly LH and rear center seat outer belt assembly out of the room partition board assembly LH and remove the room partition board assembly LH.

  18. REMOVE ROOM PARTITION BOARD ASSEMBLY RH


    1. B006DOXC01
      B006DHE Remove in this Direction

      Remove the nut.

    2. Pull in the removal direction shown in the illustration to detach the clip and claw.

    3. B006ATJ

      Detach the claw and guide and remove the belt guide of the rear seat outer belt assembly RH.

    4. B006BVVC01
      B006DHE Remove in this Direction

      Pull the rear seat outer belt assembly RH out of the room partition board assembly RH and remove the room partition board assembly RH.

  19. REMOVE CENTER ROOM PARTITION GARNISH ASSEMBLY


    1. Remove the 6 nuts.

      B006GY3C01
      *A w/o Cool Box *B w/ Cool Box

    2. Detach the clips and remove the room partition center garnish assembly.

  20. REMOVE NO. 1 SEAT RECLINING ADJUSTER ASSEMBLY LH


    1. B006AAV

      Remove the 4 nuts and No. 1 seat reclining adjuster assembly LH.

  21. REMOVE NO. 1 SEAT RECLINING ADJUSTER ASSEMBLY RH


    1. B006F5WC01
      *A w/ Ottoman

      w/ Ottoman:


      1. Disconnect the connector.

    2. Remove the 4 nuts and No. 1 seat reclining adjuster assembly RH.