ELECTRIC PARKING BRAKE ACTUATOR REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal support assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS: Click here

for V35A-FTS: Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

Parking brake actuator assembly with bracket (Including removal and installation)

  • Reset memory

  • Acquire tension sensor zero point

  • Parking brake bedding

 Electric parking brake system

Click here

*: When performing learning using the GTS.
Click here Click here

PROCEDURE


  1. RELEASE PARKING BRAKE


    1. Turn off the electric parking brake AUTO function.

    2. With the engine switch on (IG), operate the electric parking brake switch assembly to release the parking brake. Then turn the engine switch off.

      Tech Tips

      If the parking brake cannot be released, perform the forced release of parking brake.

  2. FORCED RELEASE PARKING BRAKE

    Note


    • If the parking brake cannot be released by operating the electric parking brake switch assembly, perform forced release by using electric release SST.

      Click here

    • If the parking brake cannot be released even when using electric release SST due to a malfunction in the parking brake actuator with bracket assembly, perform the following procedures.


    1. Remove the No. 1 differential support protector.

      Click here

    2. B0069KC

      Using a 4 mm long socket hexagon wrench, remove the bolt and release cable cover.

    3. B006AD4C01
      B006DHE Pull Out Direction

      Remove the cap.

    4. B006F8RC02
      B006DHE Push Direction
      B006B42 Rotate Direction

      Insert a 4 mm socket hexagon wrench into the release cable and while pushing down, rotate it counterclockwise.

    5. B006F8IC02
      B006DHE Install in this Direction

      After checking that the parking brake has been released, install the cap.

      Note

      When installing the cap, make sure it inserted facing the correct direction.

    6. B0069R2

      Using a 4 mm long socket hexagon wrench, install the release cable cover with the bolt.

      Torque:
      3.0 N*m  { 31 kgf*cm, 27 in.*lbf }

    7. Install the No. 1 differential support protector.

      Click here

  3. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  4. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

    Click here

  5. REMOVE PARKING BRAKE ACTUATOR ASSEMBLY WITH BRACKET


    1. Remove the bolt and 6 nuts to disconnect the parking brake actuator assembly with bracket from the rear suspension member sub-assembly.

      B006C9T
    2. B006D47

      Disconnect the 2 clamps from the rear suspension member sub-assembly.

    3. B006AOZ

      Remove the 3 nuts and parking brake actuator assembly with bracket.

  6. REMOVE CABLE SUPPORT BRACKET


    1. B006CZY

      Remove the cable support bracket in the direction indicated by the arrow shown in the illustration.

  7. REMOVE NO. 2 CABLE SUPPORT BRACKET


    1. B006FT8

      Remove the No. 2 cable support bracket in the direction indicated by the arrow shown in the illustration.

  8. REMOVE NO. 1 CABLE SUPPORT BRACKET


    1. B006GI0

      Remove the No. 1 cable support bracket in the direction indicated by the arrow shown in the illustration.

  9. REMOVE NO. 2 ACTUATOR HARNESS CLAMP


    1. B006EAB

      Disconnect the clamp and remove the No. 2 actuator harness clamp.

  10. REMOVE NO. 1 ACTUATOR HARNESS CLAMP


    1. B006FRJ

      Disconnect the 2 clamps and remove the No. 1 actuator harness clamp.