REAR SUSPENSION MEMBER INSTALLATION

PROCEDURE


  1. INSTALL REAR SUSPENSION MEMBER DYNAMIC DAMPER


    1. Install the 2 dynamic damper to the rear suspension member with the 4 bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
  2. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (w/o Rough Road Package 2)


    1. A004S9GE01
      *1 Front Side

      Temporarily install 2 new cushions to the rear suspension member facing in the direction shown in the illustration.

    2. A004QLSE02
      Text in Illustration
      *1 Turn
      *2 Hold

      Using SST, install the cushion so that there is no clearance between the suspension member and cushion.

      SST
      09570-24011
      09950-40011   ( 09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04061, 09957-04010, 09958-04011 )
      09950-60020   ( 09951-00710 )

      Note


      • Apply a small amount of grease to the threads of SST (center bolt) before use.

      • Do not apply excessive pressure to the center sleeve of the cushion.

  3. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION (w/o Rough Road Package 2)


    1. A004R1YE01
      *1 Front Side

      Temporarily install 2 new cushions to the rear suspension member facing in the direction shown in the illustration.

    2. A004QLSE02
      Text in Illustration
      *1 Turn
      *2 Hold

      Using SST, install the cushion so that there is no clearance between the suspension member and cushion.

      SST
      09570-24011
      09950-40011   ( 09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04061, 09957-04010, 09958-04011 )
      09950-60020   ( 09951-00710 )

      Note


      • Apply a small amount of grease to the threads of SST (center bolt) before use.

      • Do not apply excessive pressure to the center sleeve of the cushion.

  4. INSTALL PARKING BRAKE ACTUATOR SUPPORT BRACKET

    Click here

  5. INSTALL PARKING BRAKE WITH CABLE ACTUATOR ASSEMBLY

    Click here

  6. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

    CAUTION:

    As the rear suspension member is very heavy, support it with an engine lift and attachments.


    1. Lift the rear suspension member with an engine lift and attachments.

    2. A004TLE

      Connect the electrical parking brake actuator connector and push in the lock lever.

    3. A004Q4IE01
      Text in Illustration
      *1 Bolt
      *2 Nut A
      *3 Nut B

      Install the rear suspension member and 8 rear suspension member stoppers with the 2 bolts and 4 nuts.

      Torque:
      for bolt
      125 N*m  { 1275 kgf*cm, 92 ft.*lbf }
      for nut A
      61 N*m  { 620 kgf*cm, 45 ft.*lbf }
      for nut B
      125 N*m  { 1275 kgf*cm, 92 ft.*lbf }
  7. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

    A004SMN

    1. Temporarily install the upper control arm to the rear suspension member with the bolt and nut.

  8. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  10. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL REAR LOWER COIL SPRING INSULATOR LH

  12. INSTALL REAR LOWER COIL SPRING INSULATOR RH

  13. INSTALL REAR UPPER COIL SPRING INSULATOR LH

    Click here

  14. INSTALL REAR UPPER COIL SPRING INSULATOR RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. INSTALL REAR COIL SPRING LH

    Click here

  16. INSTALL REAR COIL SPRING RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

    Click here

  18. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH

    A004PB7

    1. Install the rear axle carrier to the rear upper control arm with the bolt and nut.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Since a stopper nut is used, tighten the bolt.

  20. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  22. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. CONNECT REAR TRAILING ARM ASSEMBLY LH


    1. Connect the rear trailing arm to the rear axle carrier with the 2 bolts.

      Torque:
      200 N*m  { 2039 kgf*cm, 148 ft.*lbf }
  24. CONNECT REAR TRAILING ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. INSTALL REAR STABILIZER BAR

    Click here

  26. INSTALL REAR STABILIZER LINK ASSEMBLY LH

    Click here

  27. INSTALL REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. INSTALL REAR SUSPENSION MEMBER BRACE LH

    Click here

  29. INSTALL REAR SUSPENSION MEMBER BRACE RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. INSTALL REAR FLOOR SIDE MEMBER COVER RH

    A004OWJ

    1. Attach the 2 clips to install the rear floor side member cover RH, and then install the bolt.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }
  31. INSTALL REAR SUSPENSION ARM COVER LH

    Click here

  32. INSTALL REAR SUSPENSION ARM COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  33. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (for HID Headlight)

    Click here

  34. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

    Click here

  35. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. INSTALL REAR DISC

    Click here

  37. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

    Click here

  38. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. CONNECT PARKING BRAKE CABLE AND EMERGENCY RELEASE CABLE

    Click here

  40. INSTALL FLOOR NO. 2 UNDER COVER


    1. Install the floor No. 2 under cover with the 6 clips.

  41. CONNECT SKID CONTROL SENSOR WIRE

    Click here

  42. INSTALL TAILPIPE ASSEMBLY


    1. for 1AD-FTV:

      Install the tailpipe assembly Click here.

    2. for 2AD-FTV:

      Install the tailpipe assembly Click here.

    3. for 2AD-FHV:

      Install the tailpipe assembly Click here.

  43. STABILIZE SUSPENSION

    Click here

  44. TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

    Click here

  45. TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  46. TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

    Click here

  47. TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  48. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  49. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  50. TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  51. TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  52. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  53. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }
  54. INSPECT FOR EXHAUST GAS LEAK

  55. INSPECT AND ADJUST REAR WHEEL ALIGNMENT


    1. Inspect and adjust the rear wheel alignment Click here.

  56. ADJUST HEADLIGHT ASSEMBLY


    1. for Halogen Headlight:

      Adjust the headlight assembly Click here.

    2. for HID Headlight:

      Adjust the headlight assembly Click here.

  57. INSPECT SPEED SENSOR SIGNAL


    1. Inspect the speed sensor signal Click here.

  58. PERFORM CALIBRATION


    1. Clear the electric parking brake ECU memory and perform yaw rate sensor and clutch pedal stroke sensor zero point calibration Click here.