PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED
Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | See page |
---|---|---|
Drive the vehicle until stop and start control is permitted (approximately 5 to 40 minutes) | Stop and start system | |
Correct the steering angle neutral point | Parking assist monitor system | |
Power trunk lid system not operate | Power trunk lid system |
*1: for Parking Assist Monitor System (w/ Parallel Parking Assist Function)
*2: for Parking Assist Monitor System (w/o Parallel Parking Assist Function)
Note
After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal (for Navigation System).
After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 90 seconds before disconnecting the cable from the negative (-) battery terminal (for Audio and Visual System).
PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Replacement Part | Necessary Procedure | Effect / Inoperative Function when Necessary Procedures are not Performed | See Page | |
---|---|---|---|---|
ECM | Perform Vehicle Identification Number (VIN) or frame number registration | DTC P0630 is stored | Click here for 2GR-FE Click here for 6AR-FSE Click here for 2AR-FE |
|
ECU communication ID registration (Immobiliser system) | Engine start | See Service Bulletin for the registration method. | ||
|
Inspection after repair |
|
Click here for 2AR-FE Click here for 2GR-FE |
|
|
Inspection after repair |
|
Click here for 6AR-FSE |
|
Millimeter wave radar sensor assembly | Adjust millimeter wave radar sensor assembly |
|
||
Forward recognition camera | Adjust forward recognition camera |
|
||
Engine stop and start ECU |
|
Stop and start system | ||
Air conditioning amplifier assembly*6 |
|
|||
Starter assembly*6 Note When the starter assembly is replaced, "ST relay" and "ST NO. 2 relay" must be also replaced. |
Clear number of starter operations | |||
Airbag sensor assembly*6 |
|
|||
Battery*6 |
|
|||
|
Bleed the oil pump assembly with motor (automatic transaxle assembly) | |||
Automatic transaxle assembly |
|
|
Click here for U660E Initialization Click here for U660E Registration |
|
|
|
|
||
Shift solenoid valve SL1 and/or SL2 | Perform road test to allow TCM to learn |
|
||
TCM (If possible, read the transaxle compensation code from the previous TCM) | Possible |
|
|
|
Impossible |
|
|
||
Automatic transaxle assembly |
|
|
Click here for U760E Initialization Click here for U760E Registration Click here for U761E Initialization Click here for U761E Registration |
|
|
|
|
||
Shift solenoid valve SL1 and/or SL2 | Perform road test to allow ECM to learn |
|
||
ECM (If possible, read the transaxle compensation code from the previous ECM) | Possible |
|
|
|
Impossible |
|
|
||
|
|
|
Click here for Initialization Click here for Registration |
|
Skid control ECU (Brake actuator assembly) | Perform yaw rate and acceleration sensor zero point calibration and store system information |
|
||
Yaw rate and acceleration sensor (Airbag sensor assembly) |
|
|||
Power steering ECU assembly |
|
|
||
Electric power steering column sub-assembly | Torque sensor zero point calibration | Steering effort is different between turning steering wheel to left and right | ||
Radio receiver assembly | Parking assist monitor system initialization | Parking assist monitor system (w/ Parallel Parking Assist Function) | Click here for Initialization Click here for Calibration |
|
|
|
|||
Rear television camera assembly |
|
|||
Suspension, tires, etc.*9 | Rear television camera assembly optical axis (Back camera position setting) | |||
|
|
Parking assist monitor system (w/o Parallel Parking Assist Function) | Click here for Initialization Click here for Calibration |
|
Rear television camera assembly |
|
|||
Suspension, tires, etc.*9 | Rear television camera assembly optical axis (Back camera position setting) | |||
|
Vehicle contract setting |
|
Click here for Initialization*1 Click here for Initialization*2 |
|
Radio receiver assembly*7 | Download necessary data | Some G-BOOK service content will be unavailable. | Click here for Registration*1 Click here for Registration*2 |
|
Telematics transceiver*8 | Register vehicle information | Emergency call service | ||
Mobilephone battery*8 | Reset mobilephone battery condition | |||
Blind spot monitor sensor | Blind spot monitor beam axis inspection | DTCs are output | ||
|
Code registration (Immobiliser system) |
|
See Service Bulletin for the registration method. | |
|
Initialization servo motor (Air conditioning system) | DTCs are output | ||
|
Initialize power window control system |
|
||
|
Initialize sliding roof ECU (pulse sensor initial position setting) |
|
||
|
Check power trunk lid function | Power trunk lid system | ||
|
Perform headlight leveling ECU assembly initialization | Headlight leveling function |
*1: w/ Telematics Transceiver for G-BOOK
*2: w/o Telematics Transceiver for G-BOOK
*3: for 3 Zone Type
*4: for Standard
*5: for Glass Roof
*6: w/ Stop and Start System
*7: w/ G-BOOK System
*8: w/ Telematics Transceiver except G-BOOK
*9: The vehicle height changes due to suspension or tire replacement.