NOISE FILTER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the noise filter removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	for 8GR-FKS: Click here for V35A-FTS: Click here
	Memorize steering angle neutral point	LKA/LDA system	Click here
		Parking support brake system*
		Pre-collision system
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here

*: When performing learning using the GTS.
Click here Click here

PROCEDURE

PRECAUTION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
- for 8GR-FKS:
  
  Click here
- for V35A-FTS:
  
  Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  
  Click here
- If the airbag deploys for any reason, it may cause a serious accident.
Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE REAR SEAT ASSEMBLY
1. for Fixed Seat Type:
  
  Click here
2. for Power Seat:
  
  Click here
REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)
Note

When a terminal cover is removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.
1. Remove the bolt.
2. Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
3. Remove in this Direction
  
  Detach the claw and pull out the cover as shown in the illustration.
4. Move in this Direction
  
  Using a screwdriver, detach the claws and remove the 2 terminal covers with wire harness from the condenser.
5. Move in this Direction
  
  Using a screwdriver, bend back and break off the claw as shown in the illustration.
6. Remove the terminal cover from the wire harness.
  Note
  - Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
  - Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
  - Check for deformation of the terminal after the wire harness has been removed from the terminal cover.
REMOVE PACKAGE TRAY TRIM GARNISH LH

Click here
REMOVE PACKAGE TRAY TRIM SIDE COVER LH

Click here
REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

Click here
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

Click here
REMOVE RADIO SETTING CONDENSER (for Window Defogger)
Note

When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.
1. Remove the bolt.
2. Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
3. Remove in this Direction
  
  Using a screwdriver, detach the claws and remove the terminal cover with wire harness from the condenser.
4. Using a screwdriver, bend back and break off the claw as shown in the illustration.
  Note
  
  Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
  
  Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
  
  Check for deformation of the terminal after the wire harness has been removed from the terminal cover.