REAR SEAT INNER BELT ASSEMBLY(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat inner belt assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS: Click here

for V35A-FTS: Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here


  • Rear No.1 seat adjuster assembly (removal and installation)

  • Rear No.2 seat adjuster assembly (removal and installation)

 Initialize position control ECU Rear power seat control system

Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • B006BC1

      Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

      Click here

    • B006C5U

      Wear protective gloves. Sharp areas on the parts may injure your hands.

    • There is risk of injury.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

        Click here

      • If an SRS part is accidentally deployed, it may cause a serious injury.

      B006BY6

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here


      1. for 8GR-FKS:

        Click here

      2. for V35A-FTS:

        Click here

  4. REMOVE REAR SEAT CUSHION ASSEMBLY LH

    Click here

  5. REMOVE REAR SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  7. REMOVE REAR CENTER SEAT LAP TYPE BELT ASSEMBLY RH


    1. B006CYTC01
      B006AHR Connector
      B006EC9 Nut

      Disconnect the connector and detach the clamp.

    2. Remove the nut and rear center seat lap type belt assembly RH.

  8. REMOVE REAR SEATBACK ASSEMBLY LH

    Click here

  9. REMOVE REAR SEATBACK ASSEMBLY RH

    Click here

  10. REMOVE REAR NO. 2 SEAT ADJUSTER ASSEMBLY

    Click here

  11. REMOVE REAR NO. 1 SEAT ADJUSTER ASSEMBLY

    Click here

  12. REMOVE REAR SEAT INNER BELT ASSEMBLY LH


    1. B006GIR

      Detach the wire harness clamp.

    2. Remove the bolt and rear seat inner belt assembly LH.

  13. REMOVE REAR SEAT INNER BELT ASSEMBLY RH


    1. B006EJW

      Detach the wire harness clamp.

    2. Remove the bolt and rear seat inner belt assembly RH.