OCCUPANT DETECTION SENSOR(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the occupant detection sensor removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights

Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic View Monitor System

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B006C5U

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal.

      Click here

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B006BY6

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

  3. REMOVE REAR SEAT CUSHION ASSEMBLY LH

    Click here

  4. REMOVE REAR SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. REMOVE REAR CENTER SEAT CUSHION ASSEMBLY

    Click here

  6. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  7. REMOVE SEAT CUSHION CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Click here

  8. REMOVE SEAT CUSHION CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Click here

  9. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD LH

    Click here

  10. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER LH


    1. Remove the 8 hog rings and pull out the strap from the hole of the rear seat cushion pad LH.

      B006DJH
    2. Remove the 6 hog rings and separate type rear seat cushion cover LH.

  12. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE REAR SEAT CUSHION PAD (w/ Refresh Seat)


    1. Remove the 4 hog rings and pull out the strap from the hole of the rear seat cushion pad.

      B006FIYC01
      B006FQ2 Double-sided Tape - -
    2. Remove the double-sided tape and rear seat cushion pad.

  14. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B006CI4C01

      Cut the tack pin and fold back the strap.

    2. B006EC2

      Remove the 2 pieces of felt.

    3. B006EOAC01
      B006DHE Remove in this Direction

      Detach the hook and remove the seat cushion main stretcher cushion assembly.

  15. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B006GK7

      Cut the tack pin and fold back the strap.

    2. B006E0F

      Remove the 2 pieces of felt.

    3. B006EFHC02
      B006DHE Remove in this Direction

      Detach the hook and remove the seat cushion main stretcher cushion assembly.

  17. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE REAR SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)

  19. REMOVE REAR SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)

  20. REMOVE REAR CENTER SEAT CUSHION COVER SUB-ASSEMBLY

    Click here

  21. REMOVE REAR CENTER SEAT CUSHION PAD


    1. B006DQZC01
      B006GBM Double-sided Tape

      Using a thin-bladed screwdriver wrapped with protective tape, detach the claw and disconnect the connector of the occupant detection sensor.

    2. Remove the rear center seat cushion pad from the center seat cushion frame sub-assembly.