OCCUPANT DETECTION SENSOR REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the occupant detection sensor removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS: Click here

for V35A-FTS: Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here


  • Power seat switch LH (Removal and installation)

  • Power seat switch RH (Removal and installation)

  • Front seatback frame sub-assembly LH (Removal and installation)

  • Front seatback frame sub-assembly RH (Removal and installation)

  • Front seat adjuster assembly LH (Removal and installation)

  • Front seat adjuster assembly RH (Removal and installation)

 Initialize position control ECU Front Power Seat Control System

Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • B006BC1

      Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

      Click here

    • B006B4P

      Wear protective gloves. Sharp areas on the parts may injure your hands.

    • There is risk of injury.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  3. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH

    Click here

  4. REMOVE FRONT POWER ADJUSTER SHIELD RH

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  5. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  6. REMOVE FRONT SEAT CUSHION SHIELD RH

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  7. REMOVE FRONT INNER SEAT CUSHION SHIELD RH

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  8. REMOVE FRONT SEAT FRONT CUSHION SHIELD RH

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  9. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  10. REMOVE SEAT CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

    Click here

  11. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

    Click here

  12. REMOVE SEPARATE TYPE FRONT SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)

    Tech Tips

    The occupant detection sensor cannot be removed from the separate type front seat cushion pad RH as they are a unit.


    1. B006ET1C03
      *a Band
      *b Strap

      Pull out the band of the separate type front seat cushion cover RH from the separate type front seat cushion pad RH.

    2. Remove the 4 hog rings and pull out the straps from the hole of the separate type front seat cushion pad RH.

    3. B006FOB

      Remove the 8 hog rings and separate type front seat cushion pad RH (occupant detection sensor) from the separate type front seat cover RH.