POP UP HOOD LIFTER(for Front Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the pop up hood lifter assembly removal/installation are shown below.

Necessary Procedures after parts removed/installed/replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS:

Click here

for V35A-FTS:

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic View Monitor system

Click here

Initialize Rear Door Sunshade System Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

Front bumper assembly (Including removal and installation)

  • Ultrasonic sensor detection angle

  • Ultrasonic sensor detection angle registration

 Parking support brake system

Click here

Front television camera view adjustment Panoramic view monitor system

Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:

If the hood release lever is pulled after the pop up hood lifter assembly is activated, the hood may rise more.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    Click here

    B006BC1

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    for 8GR-FKS:

    Click here

    for V35A-FTS:

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the pedestrian protection system.

    • If the pop up hood lifter deploys for any reason, it may cause a serious accident.

    B006BY6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE HEADLIGHT ASSEMBLY LH (for LH Side)

    Click here

  5. REMOVE HEADLIGHT ASSEMBLY RH (for RH Side)

    Tech Tips

    Use the same procedure for the LH side.

    Click here

  6. REMOVE FRONT AIRBAG SENSOR LH (for LH Side)

    Click here

  7. REMOVE FRONT AIRBAG SENSOR RH (for RH Side)

    Tech Tips

    Use the same procedure for the LH side.

    Click here

  8. REMOVE POP UP HOOD LIFTER ASSEMBLY LH

    CAUTION:


    • When storing the pop up hood lifter assembly LH even temporarily, be sure to keep the extended section side facing upward.

    • If the pop up hood lifter deploys for any reason, it may cause a serious accident.

    B006DRCC01
    B006GBM Extended Section

    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the pedestrian protection system.

      • If the pop up hood lifter deploys for any reason, it may cause a serious accident.

      B006BY6

    3. Disconnect pop up hood lifter connector.

      Note

      When disconnecting pop up hood lifter connector, take care not to damage the wire harness.


      1. B006C0SC01
        *a Housing Lock
        *b CPA
        *c CPA Upper Part
        B006DHE Slide

        Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter connector.

      3. After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B006F5DC07
        *a Correct *b Incorrect
        *c CPA *d Housing
    4. B006D7W

      Remove the 3 bolts.

    5. Lift up the pop up hood lifter assembly LH to detach the hook and remove it.

    6. B006D08

      While avoiding the air conditioning hose, pull out the pop up hood lifter assembly LH as shown in the illustration.

  9. REMOVE POP UP HOOD LIFTER ASSEMBLY RH

    CAUTION:


    • When storing the pop up hood lifter assembly RH even temporarily, be sure to keep the extended section side facing upward.

    • If the pop up hood lifter deploys for any reason, it may cause a serious accident.

    B006DRCC01
    B006GBM Extended Section

    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the pedestrian protection system.

      • If the pop up hood lifter deploys for any reason, it may cause a serious accident.

      B006BY6
    3. B006C0SC01
      *a Housing Lock
      *b CPA
      *c CPA Upper Part
      B006DHE Slide

      Disconnect pop up hood lifter connector.

      Note

      When disconnecting pop up hood lifter connector, take care not to damage the wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter connector.

      3. After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B006F5DC07
        *a Correct *b Incorrect
        *c CPA *d Housing
    4. B006CEV

      Remove the 3 bolts.

    5. Lift up the pop up hood lifter assembly RH to detach the hook and remove it.

    6. B006CIHC01
      B006DHE Detach Hood Lock Control assembly Cable Clamp in this Direction
      B006B42 Disconnect Hood Lock Control assembly Cable End in this Direction

      Detach the hood lock control assembly cable clamp.

    7. Disconnect the hood lock control assembly cable end.

  10. REMOVE HOOD LOCK ASSEMBLY

    Click here

  11. REMOVE HOOD LOCK CONTROL CABLE COVER RH (for RHD)

    Click here

  12. REMOVE HOOD LOCK CONTROL ASSEMBLY


    1. B006AYTC01
      B006DHE Remove in this Direction

      Pull out the hood lock control assembly to remove it.