FUEL SENDER GAUGE ASSEMBLY (for Fuel Sub Tank) INSTALLATION


  1. INSTALL FUEL SENDER GAUGE ASSEMBLY


    1. A015ACB

      Install a new gasket to the sender gauge.

    2. Install the sender gauge with the 5 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

      Note

      Be careful not to bend the arm of the fuel sender gauge.

    3. Connect the sender gauge connector.

  2. INSTALL REAR FLOOR SERVICE HOLE COVER


    1. A015BX5

      Install the service hole cover with new butyl tape.

  3. INSTALL REAR NO. 7 AIR DUCT (w/ Rear Air Conditioning System)


    1. A0158O5E01

      Attach the 4 clips to install the air duct.

      Tech Tips

      Attach the clips in the order shown in the illustration.

  4. INSTALL REAR FLOOR MAT ASSEMBLY


    1. A015B7T

      Attach the 5 clips to install the floor mat.

  5. INSTALL REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)


    1. A015AAR

      Attach the claw to install the guide.

    2. Install the screw.

      Tech Tips

      Use the same procedures for both sides.

  6. INSTALL AIR DUCT PLUG (w/ Rear Air Conditioning System)


    1. A015CYQ

      Attach the 2 claws to install the plug.

      Tech Tips

      Use the same procedures for both sides.

  7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH


    1. w/ Sliding Roof:

      Install the front quarter trim panel assembly LH Click here.

    2. w/o Sliding Roof:

      Install the front quarter trim panel assembly LH Click here.

  8. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH


    1. w/ Sliding Roof:

      Install the front quarter trim panel assembly RH Click here.

    2. w/o Sliding Roof:

      Install the front quarter trim panel assembly RH Click here.

  9. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    A015E2E

    Tech Tips

    Use the same procedure to install the rear seat cover cap on the other side.


    1. Attach the 3 claws to install the rear seat cover cap.

  10. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    A015BES

    1. Attach the 6 clips to install the support plate.

  11. INSTALL REAR DOOR SCUFF PLATE LH

    A015BJQ

    1. Attach the 3 claws and 4 clips to install the scuff plate.

    2. Install the screw.

  12. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  13. INSTALL REAR STEP COVER

    A0159DZ

    Tech Tips

    Use the same procedure to install the step cover on the other side.


    1. Attach the 2 claws to install the step cover.

  14. INSTALL REAR NO. 2 SEAT ASSEMBLY


    1. for Face to Face Seat Type:

      Install the rear No. 2 seat assembly Click here.

    2. except Face to Face Seat Type:

      Install the rear No. 2 seat assembly Click here.

  15. INSTALL REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)


    1. Install the rear No. 1 seat assembly RH Click here.

  16. INSTALL REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)


    1. Install the rear No. 1 seat assembly LH Click here.

  17. INSTALL CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    1. Connect the cables to the negative (-) main battery and sub-battery terminals.

  18. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.