ROOF HEADLINING REMOVAL

PROCEDURE


  1. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. Remove the rear No. 2 floor board.

  3. REMOVE REAR NO. 4 FLOOR BOARD


    1. Remove the rear No. 4 floor board.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  5. REMOVE REAR NO. 1 FLOOR BOARD


    1. A003LLG

      Using a clip remover, remove the 4 clips.

    2. Disengage the 2 guides to remove the rear No. 1 floor board.

  6. REMOVE DECK FLOOR BOX LH


    1. A003P8T

      Disengage the 2 claws and 5 guides to remove the deck floor box LH.

  7. REMOVE DECK FLOOR BOX RH


    1. A003LA5

      Disengage the 2 claws and 4 guides to remove the deck floor box RH.

  8. REMOVE DECK TRIM SERVICE HOLE COVER

    Click here

  9. REMOVE REAR DECK TRIM COVER


    1. A003ON0

      Remove the bolt.

    2. Disengage the 4 clips to remove the rear deck trim cover.

  10. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B006HOUC01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the claw as shown in the illustration.

      Tech Tips

      Use the same procedure for the front side and rear side.

    2. B006ICRC01
      B006IFV Remove in this Direction

      Disengage the 6 claws and 2 guides to remove the front door scuff plate LH as shown in the illustration.

  11. REMOVE COWL SIDE TRIM BOARD LH


    1. B006HIGC01
      B006IFV Remove in this Direction

      Remove the clip.

    2. Disengage the 2 clips to remove the cowl side trim board LH as shown in the illustration.

  12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  13. REMOVE FRONT PILLAR GARNISH LH


    1. B006HURC01
      B006IOI Protective Tape

      Apply protective tape around the front pillar garnish LH as shown in the illustration.

    2. B006IBCC01
      *1 Front Pillar Garnish Clip
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

      Tech Tips

      Let the front pillar garnish LH hang from the front pillar garnish clip.

    3. B006HAAC01
      *1 Front Pillar Garnish Clip
      B006IFV Remove in this Direction

      While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

      Note


      • The front pillar garnish clip is reusable if it is not damaged.

      • If the front pillar garnish clip is damaged, replace it with a new one.

      Tech Tips

      When the front pillar garnish clip cannot be disengaged easily:


      1. B006H7YC02
        B006IFV Move in this Direction

        While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip as shown in the illustration.

      2. B006HHKC02
        B006IFV Pull in this Direction

        While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.

    4. B006HG6C01
      B006IFV Remove in this Direction

      Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.

    5. B006J2JC01
      *1 Curtain Shield Airbag Assembly LH
      *a Protective Cover
      *b Adhesive Tape

      Protect the curtain shield airbag assembly LH.


      1. Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

  14. REMOVE REAR DOOR SCUFF PLATE LH


    1. B006J66C01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the claw as shown in the illustration.

    2. B006J4DC01
      B006IFV Remove in this Direction

      Disengage the 6 claws and 3 guides to remove the rear door scuff plate LH as shown in the illustration.

  15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  16. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

    Click here

  17. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

  18. REMOVE LOWER CENTER PILLAR GARNISH LH


    1. B006HF0C01
      *a Claw (A)
      *b Claw (B)
      B006J86 Place Hand Here
      B006IFV Remove in this Direction (1)
      B006IV0 Remove in this Direction (2)

      Pull the lower center pillar garnish LH in the directions indicated by the arrows (1) shown in the illustration to disengage the 2 claws (A).

    2. Pull the lower center pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 claws (B).

    3. B006IG5C01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the 3 clips to remove the lower center pillar garnish LH as shown in the illustration.

  19. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH


    1. A003KP4

      Using a clip remover, remove the 2 clips.

    2. B006I7BC01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the guide as shown in the illustration.

    3. B006IAYC01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the clip and 2 guides to remove the center pillar garnish assembly LH as shown in the illustration.

  20. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  23. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  24. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  25. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  26. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  27. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  28. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  29. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  30. REMOVE REAR SEAT ASSEMBLY

    Click here

  31. REMOVE REAR UNDER SIDE COVER LH


    1. B006I1WC01
      B006IFV Remove in this Direction

      Remove the 2 clips.

    2. Disengage the claw, 4 clips and guide to remove the rear under side cover LH as shown in the illustration.

  32. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH


    1. A003NAE

      Loosen the bolt to remove the rear seatback hinge sub-assembly LH.

  33. REMOVE REAR SEAT SIDE GARNISH LH


    1. B006IA6C01
      B006J86 Place Hand Here
      B006IFV Remove in this Direction

      Disengage the claw as shown in the illustration.

    2. B006ITKC01
      B006IFV Remove in this Direction

      Disengage the 2 clips and 2 guides to remove the rear seat side garnish LH as shown in the illustration.

  34. REMOVE ROPE HOOK (for LH Side without Toyota Safety Sense)


    1. B006HZYC01
      *a Protective Tape
      B006J86 Insert Screwdriver Here
      B006IFV Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the rope hook as shown in the illustration.

  35. REMOVE NO. 2 ROPE HOOK (for LH Side without Toyota Safety Sense)


    1. B006I3AC01
      *a Protective Tape
      B006J86 Insert Screwdriver Here
      B006IFV Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the No. 2 rope hook as shown in the illustration.

  36. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for LH Side with Toyota Safety Sense)


    1. B006IQZC01
      *a Protective Tape
      B006J86 Insert Screwdriver Here
      B006IFV Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the No. 1 tonneau cover holder cap as shown in the illustration.

  37. REMOVE TONNEAU COVER HOOK A (for LH Side with Toyota Safety Sense)


    1. B006J2PC01
      *a Protective Tape
      B006J86 Insert Screwdriver Here
      B006IFV Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the tonneau cover hook A as shown in the illustration.

  38. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. B006I2CC01
      *1 No. 2 Luggage Compartment Trim Hook

      Lower the No. 2 luggage compartment trim hook as shown in the illustration.

    2. B006HC0C02
      *1 No. 2 Luggage Compartment Trim Hook
      *a Protective Tape
      *b Hole (A)
      *c Clip
      B006J86 Insert Screwdriver Here
      B006IFV Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disengage the clip as shown in the illustration.

      Tech Tips

      Insert the screwdriver into the hole (A).

    3. B006I9MC01
      B006IR6 Screw
      B006IKP Clip

      Remove the 2 screws.

    4. Using a clip remover, remove the clip.

    5. Disengage the 5 claws, 2 clips and guide to remove the deck trim side panel assembly LH as shown in the illustration.

      B006HVSC01
      B006IFV Remove in this Direction - -

  39. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Disengage the 5 clips as shown in the illustration to remove the roof side inner garnish assembly LH.

      B006IJ3C01
      B006IFV Remove in this Direction - -

  40. REMOVE REAR UNDER SIDE COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  41. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  42. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  43. REMOVE ROPE HOOK (for RH Side without Toyota Safety Sense)

    Tech Tips

    Use the same procedure as for the LH side.

  44. REMOVE NO. 2 ROPE HOOK (for RH Side without Toyota Safety Sense)

    Tech Tips

    Use the same procedure as for the LH side.

  45. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for RH Side with Toyota Safety Sense)

    Tech Tips

    Use the same procedure as for the LH side.

  46. REMOVE TONNEAU COVER HOOK A (for RH Side with Toyota Safety Sense)

    Tech Tips

    Use the same procedure as for the LH side.

  47. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  48. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  49. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  50. REMOVE ROOF CONSOLE BOX ASSEMBLY

    Click here

  51. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    Click here

  52. REMOVE SENSOR COVER (w/ Humidity Sensor)

    Click here

  53. REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)

    Click here

  54. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  55. REMOVE RAIN SENSOR (w/ Rain Sensor)

    Click here

  56. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover)

    Click here

  57. REMOVE NO. 2 FORWARD RECOGNITION COVER

    Click here

  58. REMOVE NO. 1 FORWARD RECOGNITION COVER

    Click here

  59. REMOVE ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for all assist grip assemblies.


    1. B006IL4C01
      *a Protective Tape
      B006J86 Insert Screwdriver Here

      Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the assist grip cover LH.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    2. B006I6RC01
      B006IFV Remove in this Direction

      Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.

    3. Remove the 2 clips from the vehicle body.

  60. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the assist grip assembly.

  61. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the assist grip assembly.

  62. REMOVE VISOR BRACKET COVER (for LH Side)


    1. B006IQ6C01
      B006J86 Insert Moulding Remover Here

      Using a moulding remover, disengage the 4 claws as shown in the illustration and remove the visor bracket cover.

  63. REMOVE VISOR ASSEMBLY LH


    1. A003L4P

      for "TORX" Screw:


      1. Using a T25 "TORX" socket wrench, remove the 2 screws.

    2. except "TORX" Screw:


      1. Remove the 2 screws.

    3. B006IV4C01
      *1 Visor Holder LH
      B006IFV Remove in this Direction (1)
      B006IV0 Remove in this Direction (2)

      Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder LH.

    4. Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.

  64. REMOVE VISOR HOLDER LH


    1. B006IC7C02
      *a 45°
      B006IFV Remove in this Direction (1)
      B006IV0 Remove in this Direction (2)

      Turn the visor holder LH approximately 45° and pull it out as indicated by the arrows, in the order shown in the illustration.

    2. Disengage the 2 claws to remove the visor holder LH.

  65. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  66. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  67. REMOVE VISOR HOLDER RH

    Tech Tips

    Use the same procedure as for the LH side.

  68. REMOVE ROOF HEADLINING ASSEMBLY


    1. for Windshield Glass Side:


      1. Disconnect each connector.

    2. for Front Pillar LH Side:


      1. Remove the protective cover.

      2. A003MKH

        Using a clip remover, disengage the 4 clamps.

      3. Disconnect the 2 connectors.

      4. Install the protective cover.

    3. for Front Pillar RH Side:


      1. Remove the protective cover.

      2. B006II0C03
        *A w/ Digital Audio Broadcasting Antenna

        Using a clip remover, disengage the 3 clamps.

      3. Disconnect each connector.

      4. Install the protective cover.

    4. A003KVA

      for Rear Pillar RH Side:


      1. Disconnect the 2 connectors.

    5. Using a clip remover, remove the 3 clips.

      B006ITEC01
      *A w/ Digital Audio Broadcasting Antenna - -

    6. w/ Digital Audio Broadcasting Antenna:


      1. Disconnect the connector.

    7. B006IN3C02
      B006IFV Remove in this Direction

      Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.

      Note

      Do not damage the roof headlining assembly or vehicle interior.