FRONT POWER SEAT CONTROL SYSTEM(for RHD) Wireless Transmitter Memory Function does not Operate

DESCRIPTION

With the power switch off and the driver door closed, pressing the manual lock or unlock switch on the multiplex network master switch assembly while holding a seat memory switch (M1 switch, M2 switch or M3 switch) will register the transmitter recognition code into the seat memory switch that was pressed. After the registration is completed, the answer back buzzer sounds.

Note


  • The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

  • If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

CAUTION / NOTICE / HINT

Note

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Use the GTS to check if the CAN communication system is functioning normally Click here.

      OK
      CAN communication DTC is not output.

    NG

    GO TO CAN COMMUNICATION SYSTEM Click here

    OK

  2. CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. Check the manual lock/unlock function by using the multiplex network master switch assembly Click here.

      OK
      Manual lock/unlock function operates normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  3. CHECK ENTRY AND START SYSTEM (for Entry Function)


    1. Check the entry unlock function of entry and start system Click here.

      OK
      Entry unlock function operates normally.

    NG

    GO TO ENTRY AND START SYSTEM Click here

    OK

  4. CHECK SEAT POSITION MEMORY FUNCTION


    1. Perform a seat position memory function Click here.

    2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the seat position memory function.

      Note


      • The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

      • If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

      OK
      Seat position memory function operates normally.

    NG

    GO TO OTHER FLOW CHART (Power Seat Position is not Memorized) Click here

    OK

  5. CHECK SEAT POSITION RESTORING FUNCTION


    1. Perform a seat position restoring function Click here.

    2. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

      Note


      • The seat position will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

      • If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

      OK
      Seat position restoring function operates normally.

    NG

    GO TO OTHER FLOW CHART (Power Seat does not Return to Memorized Position) Click here

    OK

  6. READ VALUE USING GTS (FR DOOR COURTESY)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body (Main Body ECU [Multiplex Network Body ECU])
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      FR Door Courtesy Front door courtesy light switch assembly signal / ON or OFF

      ON: Driver door open

      OFF: Driver door closed

      		 -
      OK
      ON or OFF appears on the screen according to the driver door condition.

    NG

    GO TO LIGHTING SYSTEM Click here

    OK

  7. CHECK MEMORY CALL REGISTRATION FUNCTION


    1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.


      • Power switch is off

      • Press and hold the M1, M2 or M3 seat memory switch

      • Driver door closed

      • Carry the key

    2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function Click here.

      OK
      Buzzer sounds normally.

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    OK

  8. READ VALUE USING GTS (MEM SW NO. w/ KEY ID)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body (Main Body ECU [Multiplex Network Body ECU])
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID1

      MEM SW1: M1 switch linked with key ID1

      MEM SW2: M2 switch linked with key ID1

      MEM SW3: M3 switch linked with key ID1

      		 -
      Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID2

      MEM SW1: M1 switch linked with key ID2

      MEM SW2: M2 switch linked with key ID2

      MEM SW3: M3 switch linked with key ID2

      		 -
      Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID3

      MEM SW1: M1 switch linked with key ID3

      MEM SW2: M2 switch linked with key ID3

      MEM SW3: M3 switch linked with key ID3

      		 -
      Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID4

      MEM SW1: M1 switch linked with key ID4

      MEM SW2: M2 switch linked with key ID4

      MEM SW3: M3 switch linked with key ID4

      		 -
      Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID5

      MEM SW1: M1 switch linked with key ID5

      MEM SW2: M2 switch linked with key ID5

      MEM SW3: M3 switch linked with key ID5

      		 -
      Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID6

      MEM SW1: M1 switch linked with key ID6

      MEM SW2: M2 switch linked with key ID6

      MEM SW3: M3 switch linked with key ID6

      		 -
      Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID7

      MEM SW1: M1 switch linked with key ID7

      MEM SW2: M2 switch linked with key ID7

      MEM SW3: M3 switch linked with key ID7

      		 -
      OK
      On the GTS display, it is confirmed that the memory call has been registered.

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    OK

  9. CHECK MEMORY CALL FUNCTION


    1. Turn the power switch off.

    2. Close and lock all doors.

    3. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.

    4. Open the driver door and check that the driver seat moves to the memorized position Click here.

      OK
      Driver seat moves to the memorized position.

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    GO TO OTHER FLOW CHART (Wireless-linked Return Function does not Operate) Click here

  10. REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    1. Temporarily replace the main body ECU (multiplex network body ECU) with a new one Click here.


    NEXT

  11. CHECK MEMORY CALL REGISTRATION FUNCTION


    1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.


      • Power switch is off

      • Press and hold the M1, M2 or M3 seat memory switch

      • Driver door closed

      • Carry the key

    2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function Click here.

      OK
      Buzzer sounds normally.
      Result
      Result Proceed to
      OK A
      NG (for Standard Seat Type) B
      NG (for Sports Seat Type, Luxury Seat Type) C

    A

    END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

    C

    REPLACE POSITION CONTROL ECU ASSEMBLY Click here

    B

  12. REPLACE POWER SEAT SWITCH ASSEMBLY


    1. Temporarily replace the power seat switch assembly with a new or normally functioning one Click here.


    NEXT

  13. CHECK MEMORY CALL REGISTRATION FUNCTION


    1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.


      • Power switch is off

      • Press and hold the M1, M2 or M3 seat memory switch

      • Driver door closed

      • Carry the key

    2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function Click here.

      OK
      Buzzer sounds normally.

    OK

    END (POWER SEAT SWITCH ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  14. REPLACE POSITION CONTROL ECU ASSEMBLY


    1. Temporarily replace the position control ECU assembly with a new or normally functioning one.



    NEXT

  15. CHECK MEMORY CALL REGISTRATION FUNCTION


    1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.


      • Power switch is off

      • Press and hold the M1, M2 or M3 seat memory switch

      • Driver door closed

      • Carry the key

    2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function Click here.

      OK
      Buzzer sounds normally.

    OK

    END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)