HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS HOW TO PROCEED WITH TROUBLESHOOTING


  1. OPERATION FLOW

    Tech Tips

    Perform troubleshooting in accordance with the procedure below. The following is an outline of basic troubleshooting procedure. Confirm the troubleshooting procedure for the circuit you are working on before beginning troubleshooting.

  2. 1.VEHICLE BROUGHT TO WORKSHOP

  3. 2.CUSTOMER PROBLEM ANALYSIS


    1. Ask the customer about the conditions and environment when the problem occurred.

  4. 3.INSPECT AUXILIARY BATTERY VOLTAGE

  5. 4.SYMPTOM CONFIRMATION AND DTC (AND FREEZE FRAME DATA) CHECK


    1. Visually check the wire harnesses, connectors and fuses for open and short circuits.

    2. Warm up the engine to the normal operating temperature.

    3. Confirm the problem symptoms and conditions, and check for DTCs.

  6. Result
    Result Proceed to
    DTC is output Go to step 5
    DTC is not output Go to step 6
  • 5.DTC CHART


    1. Find the output DTC in the DTC chart. Look at the Trouble Area column for a list of potentially malfunctioning circuits and/or parts.

    Result
    Proceed to
    Go to step 7
  • 6.PROBLEM SYMPTOMS CHART


    1. Find the problem symptoms in the problem symptoms table. Look at the Suspected Area column for a list of potentially malfunctioning circuits and/or parts.

  • 7.CIRCUIT INSPECTION OR PARTS INSPECTION


    1. Identify the malfunctioning circuit or part.

  • 8.ADJUST, REPAIR OR REPLACE


    1. Adjust, repair or replace the malfunctioning circuit or parts.

  • 9.CONFIRMATION TEST


    1. After the adjustment, repairs or replacement of components, confirm that the malfunction no longer exists. If the malfunction does not recur, perform a confirmation test under the same conditions and in the same environment as when the malfunction first occurred.

    2. END

  • CUSTOMER PROBLEM ANALYSIS

    Tech Tips


    • When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

    • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.


  • SYMPTOM CONFIRMATION AND DIAGNOSTIC TROUBLE CODE

    Tech Tips

    The diagnostic system in this vehicle has various functions.


    • The first function is the Diagnostic Trouble Code (DTC) check. A DTC is a code stored in the ECU memory whenever a malfunction in the signal circuits to the ECU occurs. In a DTC check, a previous malfunction's DTC can be checked by a technician during troubleshooting.


    • Another function is the Input Signal Check, which checks if the signals from various switches are sent to the ECU correctly.

      By using these functions, the problem areas can be narrowed down and troubleshooting can be more effective. Diagnostic functions are incorporated in the following systems of this vehicle.

      System

      DTC Check

      (Normal Mode)

      DTC Check

      (Check Mode)

      Freeze Frame Data Sensor Check / Test Mode (Input Signal Check) Data List Active Test Customize Parameter
      SFI System (2AR-FSE, w/ EGR System) - -
      SFI System (2AR-FSE, w/o EGR System) - -
      SFI System (2GR-FXE) - -
      Hybrid Control System (2AR-FSE) -
      Hybrid Battery System (2AR-FSE) - -
      Hybrid Control System (2GR-FXE) - - -
      Hybrid Battery System (2GR-FXE) - - -
      Fuel System (2AR-FSE) - - - - - - -
      Fuel System (2GR-FXE) - - - - - - -
      Emission Control System (2AR-FSE) - - - - - - -
      Emission Control System (2GR-FXE, w/ Canister Pump Module) - - - - - - -
      Emission Control System (2GR-FXE, w/o Canister Pump Module) - - - - - - -
      Cruise Control System - - -
      Dynamic Radar Cruise Control System - - -
      Forward Recognition Camera System - - -
      Road Sign Assist System - - - -
      LKA/LDA System - -
      Hybrid Transmission System (L110) - - - - - - -
      Hybrid Transmission System (L210) - - - - - - -
      Adaptive Variable Suspension System - - -
      Tire Pressure Warning System - - -
      Electronically Controlled Brake System - -
      Electric Parking Brake System - - -
      Power Steering System (for 2AR-FSE) - - - -
      Power Steering System (for 2GR-FXE) - - - -
      Variable Gear Ratio Steering System - - -
      Dynamic Rear Steering System - - -
      Power Tilt and Power Telescopic Steering Column System - -
      Steering Lock System - - - -
      Heated Steering Wheel System - - - - - - -
      Audio and Visual System - - -
      Navigation System - - -
      Telematics System(w/ Telematics Transceiver for G-BOOK) - - - - - -
      Telematics System(w/ Telematics Transceiver except G-BOOK) - - - -
      Telematics System(w/o Telematics Transceiver for G-BOOK) - - - - - - -
      LEXUS Parking Assist-sensor System - - -
      Parking Assist Monitor System - - - - -
      Blind Spot Monitor System - - - -
      Garage Door Opener System - - - - - - -
      Charging System (2AR-FSE) - - - - - - -
      Charging System (2GR-FXE) - - - - - - -
      LIN Communication System - - - - -
      CAN Communication System (for LHD) - - - - -
      CAN Communication System (for RHD) - - - - -
      Power Door Lock Control System - - -
      Wireless Door Lock Control System - - -
      Entry and Start System (for Entry Function) - - -
      Entry and Start System (for for Start Function) - - -
      Push-button Start - - -
      Engine Immobiliser System - - - -
      Theft Deterrent System - - -
      Lighting System (INT) - - - -
      Meter / Gauge System - -
      Clock System - - - - - - -
      Headup Display System - -
      Airbag System - - - -
      Pre-crash Safety System - -
      Front Power Seat Control System (for LHD) - - -
      Front Power Seat Control System (for RHD) - - -
      Seat Heater System - - - - -
      Climate Control Seat System - - - - - -
      Seat Belt Tension Reducer System - - - - - - -
      Seat Belt Warning System - - - -
      Air Conditioning System - - -
      Rear Sunshade System - - - -
      Power Window Control System - - -
      Windshield Deicer System - - - - - -
      Window Defogger System - - - - - -
      Sliding Roof System - - -
      Luggage Compartment Door Opener System - - - -
      Luggage Compartment Door Closer System - - -
      Fuel Lid Opener System - - - - - - -
      Power Trunk Lid System - - -
      Power Mirror Control System - - - -
      Wiper and Washer System - - - - - - -
      Lighting System (EXT) - -
      AFS (Adaptive Front-lighting System) - -
      Adaptive High Beam System - -
      Automatic Headlight Beam Level Control System - - -
      Automatic High Beam System - - - -
      Horn System - - - - - - -
      Vehicle Proximity Notification System - - -
      Grille Shutter System - - - -

    • In the DTC check, it is very important to determine whether the problem indicated by the DTC either: 1) still occurs, or 2) occurred in the past but has returned to normal. In addition, the DTC should be compared to the problem symptom to see if they are related. For this reason, DTCs should be checked before and after confirmation of symptoms (i.e., whether or not problem symptoms exist) to determine current system conditions, as shown in the flowchart below.


    • Never skip the DTC check. Failing to check for DTCs, depending on the case, may result in unnecessary troubleshooting for systems operating normally or lead to repairs not related to the problem. Follow the procedure listed in the flowchart in the correct order.


    • The following flowchart shows how to proceed with troubleshooting using the DTC check. Directions from the flowchart will indicate how to proceed either to DTC troubleshooting or to the troubleshooting of each problem symptom.

  • 1.DTC CHECK

  • 2.MAKE A NOTE OF DTC DISPLAYED AND THEN CLEAR DTCs

  • 3.SYMPTOM CONFIRMATION

    Result
    Result Proceed to
    No symptoms exist Go to step 4
    Symptoms exist Go to step 5
  • 4.SIMULATION TEST USING SYMPTOM SIMULATION METHODS

  • 5.DTC CHECK

    Result
    Result Proceed to
    DTC is not output Go to step 6
    DTC is output TROUBLESHOOT FOR PROBLEM INDICATED BY DTC
  • 6.SYMPTOM CONFIRMATION

    Result
    Result Proceed to
    Symptoms exist TROUBLESHOOT FOR EACH PROBLEM SYMPTOM
    No symptoms exist END

    If a DTC was displayed in the initial DTC check, the problem may have occurred in a wire harness or connector in that circuit in the past. Check the wire harness and connectors.

    If problem symptoms are present, but no DTCs were stored again after they were cleared, then the problem causing the symptom may be occurring for something that does not store DTCs (the DTC that was displayed in the initial DTC check may have been from a past problem or a secondary problem).

  • SYMPTOM SIMULATION

    Tech Tips

    The most difficult case in troubleshooting is when no problem symptoms occur. In such a case, a thorough problem analysis must be carried out. A simulation of the same or similar conditions and environment in which the problem occurred in the customer's vehicle should be carried out. No matter how much skill or experience a technician has, troubleshooting without confirming the problem symptoms will lead to important repairs being overlooked and mistakes or delays.


    1. A000PARE11
    Text in Illustration
    *a Vibrate Slightly
    *b Shake Slightly
  • VIBRATION METHOD: When a malfunction seems to occur as a result of vibration.


    1. PARTS OR SENSORS

      Apply slight vibration with a finger to the part or sensor suspected to be the cause of the problem, and check whether the malfunction occurs.

      Note

      Applying strong vibration to relays may open the relays.

    2. CONNECTORS

      Slightly shake the connector vertically and horizontally.

    3. WIRE HARNESS

      Slightly shake the wire harness vertically and horizontally.

      Tech Tips

      The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

  • HEAT METHOD: When a malfunction seems to occur when the area in question is heated.


    1. Heat the component that is the possible cause of the malfunction with a hair dryer or similar device. Check if the malfunction occurs.

      Note


      • Do not heat components to more than 60°C (140°F). Exceeding this temperature may damage the components.

      • Do not apply heat directly to parts in an ECU.

  • A000S3P

    WATER SPRINKLING METHOD: When a malfunction seems to occur on a rainy day or in high-humidity.


    1. Sprinkle water onto the vehicle and check if the malfunction occurs.

      Note


      • Never sprinkle water directly into the engine compartment. Indirectly change the temperature and humidity by spraying water onto the front of the radiator.

      • Never apply water directly onto the electronic components.

      Tech Tips

      If the vehicle has or had a water leak problem, the leak may have damaged the ECU or connections. Look for evidence of corrosion or short circuits. Proceed with caution during water tests.

  • A000RMU

    HIGH ELECTRICAL LOAD METHOD: When a malfunction seems to occur when the electrical load is high.


    1. Turn on the heater blower, headlights, rear window defogger and all other electrical loads. Check if the malfunction recurs.

  • DIAGNOSTIC TROUBLE CODE CHART

    Look for output Diagnostic Trouble Codes (DTCs) (from the DTC checks) in the appropriate section's Diagnostic Trouble Code chart. Use the chart to determine the trouble area and the proper inspection procedure. A description of each of the chart's columns is shown in the table below.

    Item Description
    DTC Code Indicates the diagnostic trouble code.
    Detection Item Indicates the system or details of the problem.
    Trouble Area Indicates the suspected areas of the problem.
    See page Indicates the page where the inspection procedure for each circuit is to be found, or gives instruction for checking and repairs.
  • PROBLEM SYMPTOMS TABLE

    When no DTC is output but the problem still occurs, use the Problem Symptoms Table. The suspected areas (circuits or parts) for each problem symptom are shown in the table. The suspected areas are listed in order of probability. A description of each of the table columns is shown in the following table.

    Tech Tips

    In some cases, the problem is not detected by the diagnostic system even though a problem symptom occurs. It is possible that the problem occurs outside the detection range of the diagnostic system, or that the problem occurs in a completely different system.

    Item Description
    Symptom -
    Suspected Area Indicates the circuit or part which needs to be checked.
    See page Indicates the page where the inspection procedure is located.
  • INSPECTION

    A description of the main points for inspection of suspected areas is shown in the following table.

    Item Description
    Description The major role and operation of the circuit or system and its component parts are explained.
    DTC Code, DTC Detection Condition and Trouble Area Indicates the diagnostic trouble codes, DTC detection conditions and suspected areas for a problem.
    Wiring Diagram

    This is a wiring diagram for the circuit or system.

    This diagram can be used together with the Electrical Wiring Diagram to thoroughly understand the circuit.

    Wire colors are indicated by alphabetical codes. B = Black, L = Blue, R = Red, BR = Brown, LG = Light Green, V = Violet, G = Green, O = Orange, W = White, GR = Gray, P = Pink, Y = Yellow, SB = Sky Blue

    The first letter indicates the basic wire color and the second letter indicates the color of the stripe.

    Inspection Procedure This shows the procedure not only to determine whether the circuit is normal or abnormal, but also to determine whether the problem is located in the sensors, actuators, wire harness or ECU.
    Illustration of the ECU connector during the check

    The illustration shows whether the connector being checked is connected or disconnected.

    The connections for an electrical tester are indicated by (+) or (-) after the terminal name.

    For inspections between a connector and body ground, information about the ground is not shown in the illustration.