VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1210, C1336

DTC Code DTC Name
C1210 Zero Point Calibration of Yaw Rate Sensor Undone
C1336 Zero Point Calibration of Acceleration Sensor Undone

DESCRIPTION

The skid control ECU (master cylinder solenoid) receives signals from the yaw rate sensor assembly via the CAN communication system.

The yaw rate sensor assembly has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.

The DTCs are also stored when the calibration has not been completed.

DTC Code DTC Detection Condition Trouble Area
C1210 Zero point calibration of the yaw rate sensor is incomplete.

  • Zero point calibration incomplete

  • Sensor installation

  • Yaw rate sensor assembly

  • Skid control ECU (Master cylinder solenoid)
C1336 Zero point calibration of the acceleration sensor is incomplete.

CAUTION / NOTICE / HINT

Note


  • After replacing the master cylinder solenoid, perform zero point calibration and store the system information Click here.

  • After replacing the yaw rate sensor assembly, perform zero point calibration Click here.

PROCEDURE


  1. CHECK DTC (CAN COMMUNICATION SYSTEM)


    1. Check for DTCs Click here.

      Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    C

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    A

  2. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR


    1. Perform zero point calibration of the yaw rate and acceleration sensor Click here.


    NEXT

  3. PERFORM TEST MODE (SIGNAL CHECK)


    1. Turn the ignition switch off.

    2. Perform the signal check in the Test Mode Procedure Click here.

      OK
      All test mode DTCs are cleared.

    OK

    END

    NG

  4. CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION


    1. Turn the ignition switch off.

    2. Check that the yaw rate sensor assembly has been installed properly Click here.

      OK
      The sensor is tightened to the specified torque.
      The sensor is not installed at an angle.

    NG

    INSTALL YAW RATE SENSOR ASSEMBLY CORRECTLY Click here

    OK

  5. READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Deceleration Sensor

      Acceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2

      		- Changes continuously during acceleration/deceleration.
      Deceleration Sensor2

      Acceleration sensor 2 reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2

      		- Changes continuously during acceleration/deceleration.
      Yaw Rate Sensor Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s

      Vehicle stationary: 0°/s

      Right turn: -128 to 0°/s

      Left turn: 0 to 127°/s

      		 -

    6. Check that the yaw rate and acceleration sensor output value is displayed on the GTS.

      OK
      The yaw rate and acceleration sensor output value is normal.
      Result
      Result Proceed to
      NG A
      OK (for LHD) B
      OK (for RHD) C

    A

    REPLACE YAW RATE SENSOR ASSEMBLY Click here

    B

    REPLACE MASTER CYLINDER SOLENOID Click here

    C

    REPLACE MASTER CYLINDER SOLENOID Click here