DTC CHECK/CLEAR (When Using GTS)
Check for DTCs.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Read the DTCs by following the prompts on the GTS screen.
Clear the DTCs.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Operate the GTS to clear the codes.
Tech Tips
Refer to the GTS operator's manual for further details.
DTC CHECK/CLEAR (When Using SST Check Wire)
Check for DTCs.
*a | Front view of DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
Read the DTCs output from the ABS warning light and slip indicator light in the combination meter.
Tech Tips
When the system is normal, the ABS warning light and slip indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
When only 1 DTC is stored, the light outputs the same code after an interval of 4 seconds. Example: When DTC 21 is stored, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.
When 2 or more DTCs are stored, the light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.
If no code is output, inspect the TC and CG terminal circuit and the ABS warning light and slip indicator light circuits.
Trouble Area | See Procedure |
---|---|
TC and CG terminal circuit | |
ABS warning light circuit (Remains on) | |
ABS warning light circuit (Does not come on) | |
Slip indicator light circuit (Remains on) | |
Slip indicator light circuit (Does not come on) |
The codes are explained in the code table.
ABS Warning Light Display | GTS Display |
---|---|
11 | C146E |
12 | C146F |
21 | C1468 |
22 | C1469 |
23 | C146A |
24 | C146B |
25 | C1225 |
26 | C1226 |
27 | C1227 |
28 | C1228 |
31 | C1401 |
C1405 | |
C1409 | |
32 | C1402 |
C1406 | |
C1410 | |
33 | C1403 |
C1407 | |
C1411 | |
34 | C1404 |
C1408 | |
C1412 | |
35 | C1413 |
36 | C1414 |
37 | C1337 |
38 | C1415 |
39 | C1416 |
41 | C1241 |
C1417 | |
42 | C1242 |
43 | C1243 |
44 | C1419 |
C1420 | |
C1442 | |
45 | C1245 |
46 | C1421 |
C1422 | |
C1423 | |
C1424 | |
C1455 | |
C1456 | |
C1457 | |
C1458 | |
49 | C1425 |
51 | C1251 |
52 | C1252 |
53 | C1253 |
54 | C1254 |
56 | C1256 |
C1452 | |
57 | C1257 |
58 | C1453 |
C1454 | |
68 | C1268 |
94 | U0073 |
95 | U0124 |
97 | C1381 |
98 | C1336 |
A1* | U0114 |
*: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.
Slip Indicator Light Display | GTS Display |
---|---|
13 | C120A |
31 | C1432 |
C1433 | |
C1434 | |
32 | C1232 |
34 | C1435 |
C1436 | |
C1443 | |
36 | C1210 |
39 | C1336 |
43* | - |
47 | C1340 |
51 | C1201 |
53 | C1203 |
62 | U0123 |
63 | U0126 |
64 | C1380 |
65 | C1437 |
U0100 | |
66 | C1290 |
C1439 | |
C1445 | |
68 | U0130 |
98 | C1440 |
*: This DTC is output when the VSC system detects a malfunction in the ABS.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.
Clear the DTCs.
*a | Front view of DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.
Check that the ABS warning light and slip indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
Remove SST from the terminals of the DLC3.
END OF DTC CHECK/CLEAR
Turn the ignition switch to ON.
Check that the ABS warning light and slip indicator light go off within approximately 3 seconds.