REAR CENTER SEAT OUTER BELT ASSEMBLY(for Fixed Seat Type) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear center seat outer belt assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system (for Mono camera type)	for Stereo Camera type: Click here for Mono Camera type: Click here
		Lane control system (for Stereo camera type)
		Parking support brake system*
		Pre-collision system (for Stereo camera type)
		Pre-collision system (for Mono camera type)
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

PROCEDURE

PRECAUTION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
1. Disconnect the cable from the negative (-) auxiliary battery terminal.
  
  Click here
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
  
  Click here
  
  If an SRS part is accidentally deployed, it may cause a serious injury.
  Note
  
  When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
  
  Click here
REMOVE REAR SEAT CUSHION ASSEMBLY

Click here
REMOVE REAR SEAT CUSHION LOCK HOOK

Click here
REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

Click here
REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)
1. Remove the nut and floor anchor of the rear center seat outer belt assembly.
REMOVE NO. 1 SEAT ARMREST CAP

Click here
REMOVE REAR SEATBACK ASSEMBLY

Click here
REMOVE REAR SEATBACK HOLDER

Click here
REMOVE REAR DOOR SCUFF PLATE LH

Click here
REMOVE REAR DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR SEAT SIDE GARNISH LH

Click here
REMOVE REAR SEAT SIDE GARNISH RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

Click here
REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE PACKAGE TRAY TRIM GARNISH LH

Click here
REMOVE PACKAGE TRAY TRIM GARNISH RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE PACKAGE TRAY TRIM SIDE COVER LH

Click here
REMOVE PACKAGE TRAY TRIM SIDE COVER RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

Click here
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE CENTER NO. 1 SPEAKER GRILLE SUB-ASSEMBLY

Click here
REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
1. Remove in this Direction
  
  Using moulding remover A, detach the claw.
2. Pull in the removal direction shown in the illustration to detach the guide and remove the shoulder guide of the rear center seat outer belt assembly.
3. Using a clip remover, remove the 2 clips.
  
  Place Hand Here Remove in this Direction
4. Place your hands at the positions shown in the illustration and pull in the removal direction to detach the clip.
5. Pass the rear seat outer belt assembly LH, rear seat outer belt assembly RH and rear center seat outer belt assembly through the hole of the package tray trim panel assembly.
  
  Remove in this Direction - -
6. pull in the removal direction to detach the guide and remove the package tray trim panel assembly.
REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY
1. Remove the 2 bolts.
2. Detach the guide and remove the rear center seat outer belt assembly.