REAR SEAT OUTER BELT ASSEMBLY(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat outer belt assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type: Click here

for Mono Camera type: Click here

Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Stereo camera type)
Pre-collision system (for Mono camera type)
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    B004U54

    Click here

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Click here

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

        Click here

      • If an SRS part is accidentally deployed, it may cause a serious injury.

      B004UM0

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

  4. REMOVE REAR SEAT CUSHION ASSEMBLY LH

    Click here

  5. REMOVE REAR SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE REAR CENTER SEAT CUSHION ASSEMBLY

    Click here

  7. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  8. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)


    1. B004UY3

      Remove the bolt and floor anchor of the rear seat outer belt assembly LH.

  9. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)

    Click here

  11. REMOVE REAR SEATBACK ASSEMBLY LH

    Click here

  12. REMOVE REAR SEATBACK ASSEMBLY RH

    Click here

  13. REMOVE REAR CENTER SEAT ARMREST ASSEMBLY

    Click here

  14. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  15. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE REAR SEAT SIDE GARNISH LH

    Click here

  17. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE ROOM PARTITION BOARD ASSEMBLY LH

    Click here

  19. REMOVE ROOM PARTITION BOARD ASSEMBLY RH

    Click here

  20. REMOVE NO. 2 EV BATTERY INTAKE DUCT

    Click here

  21. REMOVE CENTER ROOM PARTITION GARNISH ASSEMBLY

    Click here

  22. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

    Click here

  23. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE PACKAGE TRAY TRIM GARNISH LH

    Click here

  25. REMOVE PACKAGE TRAY TRIM GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. REMOVE PACKAGE TRAY TRIM SIDE COVER LH

    Click here

  27. REMOVE PACKAGE TRAY TRIM SIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

    Click here

  29. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. REMOVE CENTER NO. 1 SPEAKER GRILLE SUB-ASSEMBLY

    Click here

  31. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. Using a clip remover, remove the 2 clips.

      B004VM7C02
      B004V32 Place Hand Here B004RMI Remove in this Direction

    2. Place your hands at the positions shown in the illustration and pull in the removal direction to detach the clip.

    3. Pass the rear seat outer belt assembly LH, rear seat outer belt assembly RH and rear center seat outer belt assembly through the hole of the package tray trim panel assembly.

      B004WFAC01
      B004RMI Remove in this Direction - -

    4. pull in the removal direction to detach the guide and remove the package tray trim panel assembly.

  32. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH


    1. B004YQ6C02
      *a Locking Button
      B004VGX Protective Tape
      B004SZX Pretensioner Connector
      B004UK4 Tension Reducer Connector

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Disconnect the tension reducer connector.

    3. Detach the clamp.

    4. B004S1X

      Remove the 2 bolts.

    5. Detach the guide and remove the rear seat outer belt assembly LH.

  33. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH


    1. B004UDRC03
      *a Locking Button
      B004VGX Protective Tape
      B004SZX Pretensioner Connector
      B004UK4 Tension Reducer Connector

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Disconnect the tension reducer connector.

    3. B004SZ3

      Remove the 2 bolts.

    4. Detach the guide and remove the rear seat outer belt assembly RH.