Click here

REAR SEAT INNER BELT ASSEMBLY(for Fixed Seat Type) REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat inner belt assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type:Click here

for Mono Camera type:Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Stereo camera type)
Pre-collision system (for Mono camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic view monitor system

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
*: When performing learning using the GTS. Click hereClick here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:
    B004U54

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Click here

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

        Click here

      • If an SRS part is accidentally deployed, it may cause a serious injury.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

  4. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY

    Click here

  5. Click here

    REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  6. Click here

    REMOVE NO. 1 SEAT ARMREST CAP

    Click here

  7. Click here

    REMOVE REAR SEATBACK ASSEMBLY

    Click here

  8. Click here

    REMOVE REAR SEATBACK HOLDER

    Click here

  9. Click here

    REMOVE REAR SEAT INNER BELT ASSEMBLY LH


    1. B004X1BC01
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Pull in the removal direction (1) to detach the claw.

    2. Detach the guide and remove the protector of the rear seat inner belt assembly LH in the removal direction (2) shown in the illustration.

    3. B004WERC02
      *a Clamp
      *b Guide
      B004SZX Bolt
      B004UK4 Connector

      Remove the bolt.

    4. Disconnect the connector and detach the clamp.

    5. Detach the guide and remove the rear seat inner belt assembly LH.

  10. Click here

    REMOVE REAR SEAT INNER BELT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. B004XFX

      Remove the bolt and rear seat inner belt anchor bracket sub-assembly LH.

  11. Click here

    REMOVE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH


    1. B004RL3C02
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Pull in the removal direction (1) to detach the claw.

    2. Detach the guide and remove the protector of the rear seat inner with center belt assembly RH in the removal direction (2) shown in the illustration.

    3. B004WPFC03
      *a Clamp
      *b Guide
      B004SZX Bolt
      B004UK4 Connector

      Remove the bolt.

    4. Disconnect the connector and detach the clamp.

    5. Detach the guide and remove the rear seat inner with center belt assembly RH.

  12. Click here

    REMOVE REAR SEAT INNER BELT ANCHOR BRACKET SUB-ASSEMBLY RH


    1. B004SRE

      Remove the bolt and rear seat inner belt anchor bracket sub-assembly RH.