REAR SEAT INNER BELT ASSEMBLY(for Power Seat)

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat inner belt assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system (for Mono camera type)	for Stereo Camera type:Click here for Mono Camera type:Click here
		Lane control system (for Stereo camera type)
		Parking support brake system*
		Pre-collision system (for Stereo camera type)
		Pre-collision system (for Mono camera type)
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here
Rear No.1 seat adjuster assembly (removal and installation) Rear No.2 seat adjuster assembly (removal and installation)	Initialize position control ECU	Rear power seat control system	Click here

*: When performing learning using the GTS. Click hereClick here

Tip:

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

Click here

PROCEDURE

Click here
PRECAUTION

CAUTION:
- Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
  Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- There is risk of injury.
Note:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
1. Disconnect the cable from the negative (-) auxiliary battery terminal.
  
  Click here
  
  CAUTION:
  - Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
    
    Click here
  - If an SRS part is accidentally deployed, it may cause a serious injury.
  Note:
  When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
  
  Click here
Click here
REMOVE REAR SEAT CUSHION ASSEMBLY LH

Click here
Click here
REMOVE REAR SEAT CUSHION ASSEMBLY RH

Tip:
Use the same procedure described for the LH side.
Click here
REMOVE REAR SEAT CUSHION LOCK HOOK

Click here
Click here
REMOVE REAR CENTER SEAT LAP TYPE BELT ASSEMBLY RH
1. Connector
  
  Nut
  
  Disconnect the connector and detach the clamp.
2. Remove the nut and rear center seat lap type belt assembly RH.
Click here
REMOVE REAR SEATBACK ASSEMBLY LH

Click here
Click here
REMOVE REAR SEATBACK ASSEMBLY RH

Click here
Click here
REMOVE REAR NO. 2 SEAT ADJUSTER ASSEMBLY

Click here
Click here
REMOVE REAR NO. 1 SEAT ADJUSTER ASSEMBLY

Click here
Click here
REMOVE REAR SEAT INNER BELT ASSEMBLY LH
1. Detach the wire harness clamp.
2. Remove the bolt and rear seat inner belt assembly LH.
Click here
REMOVE REAR SEAT INNER BELT ASSEMBLY RH
1. Detach the wire harness clamp.
2. Remove the bolt and rear seat inner belt assembly RH.

	Connector
	Nut

REAR SEAT INNER BELT ASSEMBLY(for Power Seat) REMOVAL