Click here

REAR CENTER SEAT OUTER BELT ASSEMBLY(for Power Seat) REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear center seat outer belt assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type:Click here

for Mono Camera type:Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Stereo camera type)
Pre-collision system (for Mono camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic view monitor system

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
*: When performing learning using the GTS. Click hereClick here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:
    B004U54

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Click here

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

        Click here

      • If an SRS part is accidentally deployed, it may cause a serious injury.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

  4. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY LH

    Click here

  5. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  6. Click here

    REMOVE REAR CENTER SEAT CUSHION ASSEMBLY

    Click here

  7. Click here

    REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  8. Click here

    REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

    Click here

  9. Click here

    REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)

    Tip:

    Use the same procedure described for the LH side.

  10. Click here

    REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)


    1. B004UOK

      Remove the nut and floor anchor of the rear center seat outer belt assembly.

  11. Click here

    REMOVE REAR SEATBACK ASSEMBLY LH

    Click here

  12. Click here

    REMOVE REAR SEATBACK ASSEMBLY RH

    Click here

  13. Click here

    REMOVE REAR CENTER SEAT ARMREST ASSEMBLY

    Click here

  14. Click here

    REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  15. Click here

    REMOVE REAR DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure described for the LH side.

  16. Click here

    REMOVE REAR SEAT SIDE GARNISH LH

    Click here

  17. Click here

    REMOVE REAR SEAT SIDE GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  18. Click here

    REMOVE ROOM PARTITION BOARD ASSEMBLY LH

    Click here

  19. Click here

    REMOVE ROOM PARTITION BOARD ASSEMBLY RH

    Click here

  20. Click here

    REMOVE NO. 2 EV BATTERY INTAKE DUCT

    Click here

  21. Click here

    REMOVE CENTER ROOM PARTITION GARNISH ASSEMBLY

    Click here

  22. Click here

    REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

    Click here

  23. Click here

    REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  24. Click here

    REMOVE PACKAGE TRAY TRIM GARNISH LH

    Click here

  25. Click here

    REMOVE PACKAGE TRAY TRIM GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  26. Click here

    REMOVE PACKAGE TRAY TRIM SIDE COVER LH

    Click here

  27. Click here

    REMOVE PACKAGE TRAY TRIM SIDE COVER RH

    Tip:

    Use the same procedure described for the LH side.

  28. Click here

    REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

    Click here

  29. Click here

    REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  30. Click here

    REMOVE CENTER NO. 1 SPEAKER GRILLE SUB-ASSEMBLY

    Click here

  31. Click here

    REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. B004VM7C02
      B004V32 Place Hand Here B004RMI Remove in this Direction

      Using a clip remover, remove the 2 clips.

    2. Place your hands at the positions shown in the illustration and pull in the removal direction to detach the clip.

    3. B004WFAC01
      B004RMI Remove in this Direction - -

      Pass the rear seat outer belt assembly LH, rear seat outer belt assembly RH and rear center seat outer belt assembly through the hole of the package tray trim panel assembly.

    4. pull in the removal direction to detach the guide and remove the package tray trim panel assembly.

  32. Click here

    REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY


    1. B004WGA

      Remove the 2 bolts.

    2. Detach the guide and remove the rear center seat outer belt assembly.