Click here

REAR SEAT CUSHION HEATER(for Power Seat) REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the separate type rear cushion cover removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Mono Camera type:

Click here

for Stereo Camera type:

Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic View Monitor System

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
*: When performing learning using the GTS. Click hereClick here
CAUTION:
B004VVX

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:

    • B004U54

      Be sure to read precaution thoroughly before servicing.

      Click here

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:
    B004UM0

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY LH

    Click here

  5. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  6. Click here

    REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  7. Click here

    REMOVE SEAT CUSHION CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Click here

  8. Click here

    REMOVE SEAT CUSHION CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Click here

  9. Click here

    REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD LH

    Click here

  10. Click here

    REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD RH

    Click here

  11. Click here

    REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER LH


    1. B004WP1

      Remove the 8 hog rings and pull out the strap from the hole of the rear seat cushion pad LH.

    2. Remove the 6 hog rings and separate type rear seat cushion cover LH.

  12. Click here

    REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH

    Tip:

    Use the same procedure described for the LH side.

  13. Click here

    REMOVE SEAT COVER WIRE

    Click here