Click here

REAR SEATBACK HEATER(for Fixed Seat Type) REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the separate type rear seatback cover (rear seatback heater) removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Mono Camera type:

Click here

for Stereo Camera type:

Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic View Monitor System

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
*: When performing learning using the GTS. Click hereClick here
CAUTION:
B004XN9

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

Note:

  • If the rear seat airbag assembly LH was deployed, replace the rear seat airbag assembly LH, bench type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tip:

Move both front seats to the frontmost position and collapse them to the front in advance.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:
    B004U54

    Be sure to read precaution thoroughly before servicing.

    Click here

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:
    B004UM0

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY

    Click here

  5. Click here

    REMOVE NO. 1 SEAT ARMREST CAP

    Click here

  6. Click here

    REMOVE REAR SEATBACK ASSEMBLY

    Click here

  7. Click here

    REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  8. Click here

    REMOVE REAR SEATBACK HOLDER

    Click here

  9. Click here

    REMOVE REAR SEAT HEADREST ASSEMBLY

    Click here

  10. Click here

    REMOVE REAR CENTER SEAT HEADREST ASSEMBLY

    Click here

  11. Click here

    REMOVE REAR CENTER SEAT ARMREST ASSEMBLY

    Click here

  12. Click here

    REMOVE REAR SEAT HEADREST SUPPORT

    Click here

  13. Click here

    REMOVE SEPARATE TYPE REAR SEATBACK COVER LH


    1. B004TCB

      Remove the 3 hog rings.

    2. B004XP4

      Detach the wire harness clamp.

    3. B004SA1

      Disconnect the connector.

    4. Detach the clamp and remove the seat heater control sub-assembly LH.

    5. B004TR4

      Disconnect the connector.

    6. Detach the wire harness clamps and remove the rear seat wire LH.

    7. B004VRRC01
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Remove the nut.

    8. Remove the strap in the removal direction (1) shown in the illustration.

    9. Remove the strap in the removal direction (2) shown in the illustration.

    10. B004XFS

      Remove the 15 hog rings.

    11. B004SZ9

      Pass the strap of the separate type rear seatback cover through the hole of the separate type rear seatback pad to the front side.

    12. B004WP7

      Remove the 14 hog rings and remove the separate type rear seatback cover LH.

  14. Click here

    REMOVE SEPARATE TYPE REAR SEATBACK COVER RH

    Tip:

    Use the same procedure described for the LH side.

  15. Click here

    REMOVE SEAT COVER WIRE

    Click here