REAR SEATBACK HEATER(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the separate type rear seatback cover (rear seatback heater) removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Mono Camera type:

Click here

for Stereo Camera type:

Click here

Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

    Lighting system (EXT)

  • cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic View Monitor System

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here


  • Rear seat headrest assembly LH (Including removal and installation)

  • Rear seat headrest assembly RH (Including removal and installation)

  • Rear No.1 seat adjuster assembly (Including removal and installation)

  • Rear No.2 seat adjuster assembly (Including removal and installation)

 Initialize position control ECU Rear power seat control system

Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B004VVX

Note


  • If the rear seat cushion airbag assembly LH was deployed, replace the rear seat cushion panel LH, rear seat cushion pad and separate type rear seat cushion cover with the necessary parts in accordance with the extent of the collision damage.

  • If the rear seat airbag assembly LH was deployed, replace the rear seat sub panel sub-assembly LH, separate type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • B004U54

      Be sure to read precaution thoroughly before servicing.

      Click here

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B004UM0

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE REAR SEAT CUSHION ASSEMBLY LH

    Click here

  5. REMOVE REAR SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  7. REMOVE REAR SEATBACK ASSEMBLY LH

    Click here

  8. REMOVE REAR SEATBACK ASSEMBLY RH

    Click here

  9. REMOVE NO. 1 SEATBACK CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Click here

  10. REMOVE NO. 1 SEATBACK CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  11. REMOVE NO. 2 SEATBACK CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Click here

  12. REMOVE NO. 2 SEATBACK CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE REAR SEAT HEADREST ASSEMBLY LH

    Click here

  14. REMOVE REAR SEAT HEADREST ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. REMOVE REAR SEAT HEADREST SUPPORT

    Click here

  16. REMOVE SEATBACK CHECK VALVE WITH BRACKET LH

    Click here

  17. REMOVE SEATBACK CHECK VALVE WITH BRACKET RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE REAR SEAT WIRE LH

    Click here

  19. REMOVE REAR SEAT WIRE RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY LH

    Click here

  21. REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE REAR SEATBACK MAIN FRAME SUB-ASSEMBLY LH

    Click here

  23. REMOVE REAR SEATBACK MAIN FRAME SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE NO. 2 REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY

    Click here

  25. REMOVE NO. 1 REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY

    Tech Tips

    Use the same procedure described for the rear No. 2 seat headrest adjuster sub-assembly.

  26. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD LH

    Click here

  27. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE SEPARATE TYPE REAR SEATBACK COVER LH


    1. B004RAO

      Pull out the strap and bracket of the separate type rear seatback cover LH from the hole of the separate type rear seatback pad LH.

    2. B004UQM

      Remove the 2 hog rings and separate type rear seatback cover LH.

  29. REMOVE SEPARATE TYPE REAR SEATBACK COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. REMOVE SEAT COVER WIRE

    Click here