AIR PUMP(for Rear Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the lumber support pump sub-assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system (for Mono camera type)	for Mono Camera type: Click here for Stereo Camera type: Click here
		Lane control system (for Stereo camera type)
		Parking support brake system*
		Pre-collision system (for Mono camera type)
		Pre-collision system (for Stereo camera type)
		Adaptive high beam system
		Lighting system (EXT) cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic View Monitor System	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.

Note

If the rear seat cushion airbag assembly LH was deployed, replace the rear seat cushion panel LH, rear seat cushion pad and separate type rear seat cushion cover with the necessary parts in accordance with the extent of the collision damage.
If the rear seat airbag assembly LH was deployed, replace the rear seat sub panel sub-assembly LH, separate type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage.
Replace any other damaged parts as necessary.

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

PROCEDURE

PRECAUTION
CAUTION:
- Be sure to read precaution thoroughly before servicing.
  
  Click here
Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE REAR SEAT CUSHION ASSEMBLY LH

Click here
REMOVE REAR SEAT CUSHION ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR SEAT CUSHION LOCK HOOK

Click here
REMOVE REAR SEATBACK ASSEMBLY LH

Click here
REMOVE REAR SEATBACK ASSEMBLY RH

Click here
REMOVE NO. 1 SEATBACK CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

Click here
REMOVE NO. 1 SEATBACK CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

Tech Tips

Use the same procedure described for the LH side.
REMOVE NO. 2 SEATBACK CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

Click here
REMOVE NO. 2 SEATBACK CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

Tech Tips

Use the same procedure described for the LH side.
REMOVE SEATBACK CHECK VALVE WITH BRACKET LH

Click here
REMOVE SEATBACK CHECK VALVE WITH BRACKET RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY LH
1. Disconnect the connector.
2. Detach the wire harness clamp.
3. Remove the tube from the clamp.
  
  *A w/o Refresh Seat *B w/ Refresh Seat
4. Remove the 2 nuts and lumbar support pump sub-assembly LH.
REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.