REAR SEAT ASSEMBLY(for Fixed Seat Type) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type: Click here

for Mono Camera type: Click here

Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

    Lighting system (EXT)

  • cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B004XN9

Note


  • If the rear seat airbag assembly LH was deployed, replace the rear seat airbag assembly LH, bench type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips

Move both front seats to the frontmost position and collapse them to the front in advance.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    B004U54

    Click here

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Click here

      CAUTION:

      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • SRS parts are equipped with a backup power source. If work is started within 90 seconds of turning the power switch off and disconnecting the cable from the negative (-) auxiliary battery terminal, SRS parts may deploy.

      Note

      After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

      Click here

  4. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. B004S4SC01
      B004RMI Remove in this Direction
      B004V32 Place Hand Here

      Place your hand in the position shown in the illustration and lift the front end of the rear seat cushion assembly in the removal direction shown in the illustration. Detach the hooks at the front of the rear seat cushion assembly from the rear seat cushion lock hooks.

      Note


      • Be sure to detach the hooks at the front of rear seat cushion one at a time.

      • If the hook on the front of the rear seat cushion assembly is detached, replace the rear seat cushion lock hook with a new one.

    2. B004WLRC01
      B004RMI Remove in this Direction

      Detach the hooks at the rear end of the bench type rear seat cushion assembly from the bench type rear seatback assembly.

    3. w/ Seat Heater System:


      1. B004WJW

        Disconnect the 2 seat heater connectors.

    4. Remove the bench type rear seat cushion assembly.

      Note

      Do not damage the bench type rear seat cushion assembly, body or body interior.

    5. B004WAC

      w/ Seat Belt Warning System:


      1. Disconnect the connector.

      2. Detach the clamp.

  5. REMOVE NO. 1 SEAT ARMREST CAP


    1. Lift up the center headrest assembly so that the No. 1 seat armrest cap is visible.

    2. B004SRKC01
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claws and guides and remove the No. 1 seat armrest cap.

  6. REMOVE REAR SEATBACK ASSEMBLY


    1. B004SNNC01
      B004UK4 Rear Seat Airbag Assembly Connector

      Disconnect the rear seat center armrest assembly connector.

    2. Detach the guide and claw of the connector holder.

    3. Disconnect the 2 connectors of the seat wire.

    4. Disconnect the 2 connectors of the rear seat airbag assembly.


      1. Push down the white housing lock and slide the yellow CPA.

        B004XJXC29
        *a Housing Lock *b CPA

        Note


        • Do not pull while holding the wire harness.

        • Do not try to release the lock while holding down the top of the CPA (A in the illustration), as this prevents the lock from being released.

    5. B004VIBC01
      B004RMI Remove in this Direction

      Detach the button and remove the belt band.

    6. B004YFG

      Remove the 2 bolts and floor anchor of the rear seat outer belt assembly RH and rear seat outer belt LH.

    7. Remove the nut and disconnect the floor anchor of the rear center seat outer belt assembly.

    8. B004R9ZC01
      B004RMI Remove in this Direction

      Remove the 4 bolts and nut.

    9. Detach the hooks and remove the bench type rear seatback assembly.

      Note


      • Do not damage the bench type rear seatback assembly, body or body interior.

      • Several people are required when carrying the bench type rear seatback assembly out of the vehicle.

  7. REMOVE REAR SEAT CUSHION LOCK HOOK

    Note


    • If the hook on the front of the rear seat cushion assembly is detached, replace the rear seat cushion lock hook with a new one.

    • Do not reuse the removed rear seat cushion lock hook.

    Tech Tips

    Use the same procedure for the 3 parts.


    1. B004XY9C06
      *a Body
      *b Sleeve

      Insert 2 thin-bladed screwdrivers between the rear seat cushion lock hook sleeve and body as shown in the illustration.

    2. Pull up the 2 thin-bladed screwdrivers to detach the claws and remove the rear seat cushion lock hook.

  8. REMOVE REAR SEATBACK HOLDER

    Note


    • If the hook on the rear seatback assembly is detached, replace the rear seatback holder with a new one.

    • Do not reuse the removed rear seatback holder.

    Tech Tips

    Use the same procedure for the opposite side.


    1. B004WSJC01
      B004RMI Remove in this Direction

      Detach the claws and guides and remove rear seatback holder.

  9. REMOVE REAR NO. 1 SEATBACK SET BRACKET

    Tech Tips

    Use the same procedure for the opposite side.


    1. B004RD9

      Remove the bolt.

    2. Detach the guide and remove the rear No. 1 seatback set bracket.

  10. REMOVE REAR NO. 2 SEATBACK SET BRACKET


    1. B004WVP

      Remove the 2 bolts.

    2. Detach the guides and rear No. 2 seatback set bracket.