CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the curtain shield airbag assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system (for Mono camera type)	for Mono Camera type: Click here for Stereo Camera type: Click here
		Lane control system (for Stereo camera type)
		Parking support brake system*
		Pre-collision system (for Mono camera type)
		Pre-collision system (for Stereo camera type)
		Adaptive high beam system
		Lighting system (EXT) cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic View Monitor System	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here
w/ Occupant Classification System: Front seat assembly RH (Only for removal and installation)	Zero point calibration (Occupant classification system)	Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger)	Click here

*: When performing learning using the GTS. Click hereClick here

Tip:

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

Click here

PROCEDURE

Click here
PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

Note:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Note:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
Click here
REMOVE ROOF HEADLINING ASSEMBLY

Click here

Click here

REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

CAUTION:

Deployment Side

When storing the curtain shield airbag assembly LH, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.

Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.

*a	Lock Button
	Protective Tape
	Release in this Direction

Using a screwdriver, release the lock button and disconnect the airbag connector.

Note:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

Tip:

Tape the screwdriver tip before use.

Using needle-nose pliers, remove the pin from the clip A.

Tip:
Use the same procedure for the opposite side.
Using 2 thin bladed screwdrivers, detach the claw and remove the clip A.

Tip:
Use the same procedure for the opposite side.
Using a clip remover, detach the clip B.

Note:
If the clip B has been removed, replace it with a new one.

Tip:
Tape the clip remover tip before use.
Detach the claw.
Remove the 4 bolts and deployment portion of the curtain shield airbag assembly LH.

Note:
The bolt must not be reused.

*a	Clip A	*b	Clip B
	Protective Tape	-	-

Remove the 2 bolts and detach the hook to remove the curtain shield airbag assembly LH inflator.

Note:

The bolt must not be reused.

CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL