AIRBAG SYSTEM, Diagnostic DTC:B1905, B1906, B1907, B1908

DTC Code DTC Name
B1905 Short in Front P/T Squib LH Circuit
B1906 Open in Front P/T Squib LH Circuit
B1907 Short in Front P/T Squib LH Circuit (To Ground)
B1908 Short in Front P/T Squib LH Circuit (To B+)

DESCRIPTION

The front pretensioner LH circuit consists of the airbag ECU assembly and front seat outer belt assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1905 Short in Front P/T Squib LH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects a line short circuit signal 5 times in the front pretensioner LH circuit during the primary check.

  • A front seat outer belt assembly LH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Front seat outer belt assembly LH

  • Airbag ECU assembly

 Comes on Applicable
B1906 Open in Front P/T Squib LH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects an open circuit signal in the front pretensioner LH circuit for 2 seconds.

  • A front seat outer belt assembly LH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Front seat outer belt assembly LH

  • Airbag ECU assembly

 Comes on Applicable
B1907 Short in Front P/T Squib LH Circuit (To Ground)

One of the following conditions is met:


  • The airbag ECU assembly detects a short circuit to ground signal in the front pretensioner LH circuit for 0.5 seconds.

  • A front seat outer belt assembly LH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Front seat outer belt assembly LH

  • Airbag ECU assembly

 Comes on Applicable
B1908 Short in Front P/T Squib LH Circuit (To B+)

One of the following conditions is met:


  • The airbag ECU assembly detects a short circuit to B+ signal in the front pretensioner LH circuit for 0.5 seconds.

  • A front seat outer belt assembly LH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Front seat outer belt assembly LH

  • Airbag ECU assembly

 Comes on Applicable

WIRING DIAGRAM

B004W3LE59
*a Front Seat Outer Belt Assembly LH
*b Airbag ECU Assembly

CAUTION / NOTICE / HINT

Note


  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

Tech Tips

To perform the simulation method, enter check mode (signal check) with the GTS (Click here ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road Click here.

PROCEDURE


  1. CHECK CONNECTORS


    1. B004WUYC34
      *1 Front Seat Outer Belt Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag ECU assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the front seat outer belt assembly LH and airbag ECU assembly.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the floor wire connector (on the front seat outer belt assembly LH side) is not loose, deformed or damaged.

      OK
      The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

      OK
      The short springs are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  2. CHECK FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B004V5IC32
      *1 Front Seat Outer Belt Assembly LH
      *2 Airbag ECU Assembly
      *3 SST
      *a

      Front view of wire harness connector

      (to Front Seat Outer Belt Assembly LH)

      Connect the connector to the airbag ECU assembly.

    2. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the front seat outer belt assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    4. Turn the power switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1905, B1906, B1907 and B1908 are not output
      DTC B1905, B1906, B1907 or B1908 is output

      Tech Tips

      Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    11. Disconnect SST from connector C.


    DTC B1905, B1906, B1907 and B1908 are not output

    REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH Click here

    DTC B1905, B1906, B1907 or B1908 is output

  3. CHECK FLOOR WIRE


    1. B004TVOC10
      *1 Front Seat Outer Belt Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Seat Outer Belt Assembly LH)
      B004SZX Release the activation prevention mechanism

      Disconnect the floor wire from the airbag ECU assembly.

    2. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) auxiliary battery terminal.

      2. Turn the power switch on (IG).

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        L24-1 (L+) - Body ground Power switch on (IG) Below 1 V
        L24-2 (L-) - Body ground Power switch on (IG) Below 1 V

      4. Turn the power switch off.

      5. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Check for an open in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        L24-1 (L+) - L24-2 (L-) Always Below 1 Ω

    4. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        L24-1 (L+) - Body ground Always 1 MΩ or higher
        L24-2 (L-) - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B.

        Click here

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        L24-1 (L+) - L24-2 (L-) Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK DTC


    1. B004VGAC09
      *1 Front Seat Outer Belt Assembly LH
      *2 Airbag ECU Assembly

      Connect the connectors to the front seat outer belt assembly LH and airbag ECU assembly.

    2. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    3. Turn the power switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1905, B1906, B1907 and B1908 are not output
      DTC B1905, B1906, B1907 or B1908 is output

      Tech Tips

      Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.


    DTC B1905, B1906, B1907 and B1908 are not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B1905, B1906, B1907 or B1908 is output

    REPLACE AIRBAG ECU ASSEMBLY Click here