Click here

AIRBAG SYSTEM, Diagnostic DTC:B1880, B1881, B1882, B1883

Click here
Click here Click here
DTC Code DTC Name
B1880 Short in Rear Seat Cushion Squib RH Circuit
B1881 Open in Rear Seat Cushion Squib RH Circuit
B1882 Short to GND in Rear Seat Cushion Squib RH Circuit
B1883 Short to B+ in Rear Seat Cushion Squib RH Circuit
Click here

DESCRIPTION

The rear seat cushion squib RH circuit consists of the airbag ECU assembly and rear seat cushion airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear seat cushion squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1880 Short in Rear Seat Cushion Squib RH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects a line short circuit signal 5 times in the rear seat cushion squib RH circuit during the primary check.

  • A rear seat cushion airbag assembly RH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Rear seat wire RH

  • Rear seat cushion airbag assembly RH

  • Airbag ECU assembly

 Comes on Applicable
B1881 Open in Rear Seat Cushion Squib RH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects an open circuit signal in the rear seat cushion squib RH circuit for 2 seconds.

  • A rear seat cushion airbag assembly RH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Rear seat wire RH

  • Rear seat cushion airbag assembly RH

  • Airbag ECU assembly

 Comes on Applicable
B1882 Short to GND in Rear Seat Cushion Squib RH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects a short circuit to ground signal in the rear seat cushion squib RH circuit for 0.5 seconds.

  • A rear seat cushion airbag assembly RH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Rear seat wire RH

  • Rear seat cushion airbag assembly RH

  • Airbag ECU assembly

 Comes on Applicable
B1883 Short to B+ in Rear Seat Cushion Squib RH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects a short circuit to B+ signal in the rear seat cushion squib RH circuit for 0.5 seconds.

  • A rear seat cushion airbag assembly RH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Rear seat wire RH

  • Rear seat cushion airbag assembly RH

  • Airbag ECU assembly

 Comes on Applicable
Table 1. *a RCR+ *b RCR- *c Rear Seat Cushion Airbag Assembly RH *d Airbag ECU Assembly
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

Tip:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK CONNECTORS


    1. B004VWKC04
      *1 Rear Seat Cushion Airbag Assembly RH
      *2 Airbag ECU Assembly
      *3 Rear Seat Wire RH
      *4 Floor Wire

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the rear seat cushion airbag assembly RH and airbag ECU assembly.

      OK
      The connectors are properly connected.
      Tip:

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the rear seat cushion airbag assembly RH and airbag ECU assembly.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

      OK
      The short springs are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPLACE FLOOR WIRE OR REAR SEAT WIRE RH

  2. Click here

    CHECK REAR SEAT CUSHION AIRBAG ASSEMBLY RH


    1. B004TDFC02
      *1 Rear Seat Cushion Airbag Assembly RH
      *2 Airbag ECU Assembly
      *3 SST
      *a

      Front view of wire harness connector

      (to Rear Seat Cushion Airbag Assembly RH)

      Connect the connector to the airbag ECU assembly.

    2. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the rear seat cushion airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.

      Note:

      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      09843-18061

    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    4. Turn the power switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B1880, B1881, B1882 and B1883 are not output
      DTC B1880, B1881, B1882 or B1883 is output
      Tip:

      Codes other than DTC B1880, B1881, B1882 and B1883 may be output at this time, but they are not related to this check.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    11. Disconnect SST from connector C.


    • DTC B1880, B1881, B1882 and B1883 are not output

      REPLACE REAR SEAT CUSHION AIR BAG ASSEMBLY RHClick here

    • DTC B1880, B1881, B1882 or B1883 is outputClick here
  3. Click here

    CHECK REAR SEAT CUSHION AIRBAG ASSEMBLY RH CIRCUIT


    1. B004W5EC02
      *1 Rear Seat Cushion Airbag Assembly RH
      *2 Airbag ECU Assembly
      *3 Rear Seat Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Seat Cushion Airbag Assembly RH)
      B004SZX Release the activation prevention mechanism

      Disconnect the floor wire from the airbag ECU assembly.

    2. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

      2. Turn the power switch on (IG).

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        R28-1 - Body ground Power switch on (IG) Below 1 V
        R28-2 - Body ground Power switch on (IG) Below 1 V

      4. Turn the power switch off.

      5. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Check for an open in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R28-1 - R28-2 Always Below 1 Ω

    4. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R28-1 - Body ground Always 1 MΩ or higher
        R28-2 - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B.

        Click here

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R28-1 - R28-2 Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result
      Proceed to
      OK
      NG

  4. Click here

    CHECK DTC


    1. B004YU2C03
      *1 Rear Seat Cushion Airbag Assembly RH
      *2 Airbag ECU Assembly

      Connect the connectors to the rear seat cushion airbag assembly RH and airbag ECU assembly.

    2. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    3. Turn the power switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B1880, B1881, B1882 and B1883 are not output
      DTC B1880, B1881, B1882 or B1883 is output
      Tip:

      Codes other than DTC B1880, B1881, B1882 and B1883 may be output at this time, but they are not related to this check.


    • DTC B1880, B1881, B1882 and B1883 are not output

      USE SIMULATION METHOD TO CHECKClick here

    • DTC B1880, B1881, B1882 or B1883 is output

      REPLACE AIRBAG ECU ASSEMBLYClick here

  5. Click here

    CHECK FLOOR WIRE


    1. B004UZOC02
      *1 Rear Seat Airbag Assembly RH
      *2 Airbag ECU Assembly
      *3 Rear Seat Wire RH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Seat Airbag Assembly RH)
      B004SZX Release the activation prevention mechanism

      Disconnect the floor wire from the rear seat wire RH.

    2. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

      2. Turn the power switch on (IG).

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        LR 7-1 (RCR+) - Body ground Power switch on (IG) Below 1 V
        LR 7-2 (RCR-) - Body ground Power switch on (IG) Below 1 V

      4. Turn the power switch off.

      5. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Check for an open in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        LR 7-1 (RCR+) - LR 7-2 (RCR-) Always Below 1 Ω

    4. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        LR 7-1 (RCR+) - Body ground Always 1 MΩ or higher
        LR 7-2 (RCR-) - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B.

        Click here

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        LR 7-1 (RCR+) - LR 7-2 (RCR-) Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE REAR SEAT WIRE RH

    • NG

      REPLACE FLOOR WIRE