Click here

AIRBAG SYSTEM, Diagnostic DTC:B167B, B167C

Click here
Click here Click here
DTC Code DTC Name
B167B Lost Communication with Front Door Pressure Sensor LH
B167C Front Door Pressure Sensor LH Initialization Incomplete
Click here

DESCRIPTION

The circuit for the side collision sensor LH is composed of the airbag ECU assembly, side airbag sensor assembly LH and door side airbag sensor LH.

The side airbag sensor assembly LH and door side airbag sensor LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbag should be deployed.

DTC B167B or B167C is stored when a malfunction is detected in the circuit for the side collision sensor LH.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B167B Lost Communication with Front Door Pressure Sensor LH

One of the following conditions is met:


  • The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

  • A door side airbag sensor LH malfunction.

  • A side airbag sensor assembly LH malfunction.

  • A rear airbag sensor RH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Front door wire LH

  • Door side airbag sensor LH

  • Side airbag sensor assembly RH

  • Rear airbag sensor LH

  • Airbag ECU assembly

 Comes on Not applicable
B167C Front Door Pressure Sensor LH Initialization Incomplete

One of the following conditions is met:


  • The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

  • A door side airbag sensor LH malfunction.

  • A side airbag sensor assembly LH malfunction.

  • A rear airbag sensor RH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Front door wire LH

  • Door side airbag sensor LH

  • Side airbag sensor assembly RH

  • Rear airbag sensor LH

  • Airbag ECU assembly

 Comes on Not applicable
Table 1. *a Rear Airbag Sensor LH *b Door Side Airbag Sensor LH *c Side Airbag Sensor Assembly LH *d Airbag ECU Assembly
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

Click here

PROCEDURE


  1. Click here

    CHECK DTC


    1. Turn the power switch off.

    2. Turn the power switch on (IG), and wait for at least 60 seconds.

    3. Clear the DTCs stored in memory.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B167B or B167C is output
      DTC B167B and B167C are not output
      Tip:

      Codes other than DTC B167B and B167C may be output at this time, but they are not related to this check.


    • DTC B167B or B167C is outputClick here
    • DTC B167B and B167C are not output

      USE SIMULATION METHOD TO CHECKClick here

  2. Click here

    CHECK CONNECTION OF CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the rear airbag sensor LH and door side airbag sensor LH.

      Result
      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    • The connectors are properly connectedClick here
    • The connectors are not properly connected

      CONNECT CONNECTORS PROPERLY

  3. Click here

    CHECK CONNECTORS


    1. B004XQSC06
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 Floor Wire

      Disconnect the connectors from the side airbag sensor assembly LH and door side airbag sensor LH.

    2. Check that the connectors (on the side airbag sensor assembly LH side and door side airbag sensor LH side) are not damaged.

      Result
      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    • The connectors are not deformed or damagedClick here
    • The connectors are deformed or damaged

      REPLACE FRONT DOOR WIRE LH OR FLOOR WIRE

  4. Click here

    CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT


    1. B004VY7C10
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H27-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
      H27-1 (BDL-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H27-2 (BDL+) - H27-1 (BDL-) Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H27-2 (BDL+) - H27-1 (BDL-) Always 1 MΩ or higher
      H27-2 (BDL+) - Body ground Always 1 MΩ or higher
      H27-1 (BDL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

  5. Click here

    CHECK DOOR SIDE AIRBAG SENSOR LH


    1. B004XQ8C07
      *1 Door Side Airbag Sensor RH
      *2 Side Airbag Sensor Assembly LH

      Connect the connector to the side airbag sensor assembly LH and door side airbag sensor LH.

    2. Interchange the door side airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    4. Turn the power switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B166D or B166E is output
      DTC B167B or B167C is output
      DTC B166D, B166E, B167B and B167C are not output
      Tip:

      Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    11. Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.


    • DTC B166D or B166E is output

      REPLACE DOOR SIDE AIR BAG SENSOR LHClick here

    • DTC B167B or B167C is outputClick here
    • DTC B166D, B166E, B167B and B167C are not output

      USE SIMULATION METHOD TO CHECKClick here

  6. Click here

    CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B004VAHC09
      *1 Side Airbag Sensor Assembly RH
      *2 Rear Airbag Sensor LH

      Interchange the side airbag sensor assembly LH with RH and connect the connectors to them.

    2. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    3. Turn the power switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B166D or B166E is output
      DTC B167B or B167C is output
      DTC B166D, B166E, B167B and B167C are not output
      Tip:

      Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    10. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors to them.


    • DTC B166D or B166E is output

      REPLACE REAR AIRBAG SENSOR LHClick here

    • DTC B167B or B167C is output

      REPLACE AIRBAG ECU ASSEMBLYClick here

    • DTC B166D, B166E, B167B and B167C are not output

      USE SIMULATION METHOD TO CHECKClick here

  7. Click here

    CHECK FLOOR WIRE


    1. B004TNEC09
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Disconnect the floor wire connector from the front door wire LH.

    2. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L 2-10 (BDL+) - Body ground Power switch on (IG) Below 1 V
      L 2-20 (BDL-) - Body ground Power switch on (IG) Below 1 V

    5. Turn the power switch off.

    6. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    7. Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L 2-10 (BDL+) - L 2-20 (BDL-) Always Below 1 Ω

    9. Disconnect the service wire from connector B.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L 2-10 (BDL+) - L 2-20 (BDL-) Always 1 MΩ or higher
      L 2-10 (BDL+) - Body ground Always 1 MΩ or higher
      L 2-20 (BDL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE FRONT DOOR WIRE LH

    • NG

      REPLACE FLOOR WIRE